Agilent 16440A SMU - Manuals

Page 2 - Legal Notice

2 A gilent 16440A User’s Guide, Edition 4 Legal Notice The information contained in this document is subject to change without notice. Copyright © 1994 - 2000 Agilent Technologies This document contains information which is protected by copyright. All rights are reserved. Reproduction, adaptation, o...

Page 6 - Printing History

6 A gilent 16440A User’s Guide, Edition 4 • Herstellerbescheinigung GEÄUSCHEMISSION Lpa < 70 dB am Arbeitsplatz normaler Betrieb nach DIN 45635 T. 19 • Manufacturer’s Declaration ACOUSTIC NOISE EMISSION Lpa < 70dB operator position normal operation per ISO 7779 Printing History Edition 1: Febr...

Page 9 - Introduction

Agilent 16440A User’s Guide, Edition 4 3 User's Guide Introduction Introduction The 16440A selector contains the following accessories: NOTE Inspecting the 16440A upon Receiving When the 16440A arrives at your site, make sure that nothing is missing or damaged. Unpack the carton, then check the cont...

Page 10 - Operation

4 Agilent 16440A User’s Guide, Edition 4 User's GuideOperation Operation This section describes the operating theory of the selector. Agilent 4155/4156 can control the selector to automatically switch the unit (SMU or PGU) that is connected to a DUT pin according to the state (stress force state or ...

Page 13 - Installation; To Attach the Selector to Test Fixture

Agilent 16440A User’s Guide, Edition 4 7 User's Guide Installation Installation This section describes how to attach the selector to Agilent 16442A test fixture or to a shielding box, and how to connect it to Agilent 4155/4156. To Attach the Selector to Test Fixture You can attach your selector to t...

Page 16 - To Attach the Selector to Shielding Box

10 Agilent 16440A User’s Guide, Edition 4 User's GuideInstallation To Attach the Selector to Shielding Box You can attach your selector to a shielding box. You need a standard screwdriver. The following figure shows the spacing of the 16440A screw holes. You need to prepare four screws and nuts to m...

Page 22 - Maintenance; Cleaning the Selector; Servicing the Selector

16 Agilent 16440A User’s Guide, Edition 4 User's GuideMaintenance Maintenance This section provides the following maintenance information: • Cleaning • Servicing Cleaning the Selector To maintain high performance, the selector must be kept clean. Oil, perspiration, hair, dust, and dirt will degrade ...

Page 23 - Circuit Block Diagram

Agilent 16440A User’s Guide, Edition 4 17 User's Guide Maintenance Circuit Block Diagram

Page 24 - Replaceable Parts

18 Agilent 16440A User’s Guide, Edition 4 User's GuideMaintenance Replaceable Parts When soldering, use low hydrochloric acid solder (Agilent part number: 8090-0433) to prevent the flux in the solder from spreading unnecessarily, and make sure that adjacent terminals are not bridged. After soldering...

Page 26 - Specifications

20 Agilent 16440A User’s Guide, Edition 4 User's GuideSpecifications Specifications The "supplemental information" and "typical" entries, in the following specifications are not warranted, but provide useful information about the functions and performance of the instruments. The foll...

Page 28 - Supplemental Information

22 Agilent 16440A User’s Guide, Edition 4 User's GuideSpecifications Supplemental Information The following reference data is specified at 23 ± 5 ° C (73 ± 9 ° F) and 50 % relative humidity. • SMU channel Leakage current less than 100 fA at 100 V Residual resistance 0.2 W typical Stray capacitance (...