AEG PE4510-M- Manuals

8 Amportant! Do not use the appliance when extracted. Make sure the appliance is inac-tive before extracting it. N.B.! Use original or manufacturer re- commended accessories and spare parts only. Designated use This appliance is designed and made to preparecoffee and heat drinks. All other use is co...

9 B14. "jug" icon to make a number of cups of coffee directly in the jug (provided) PRELIMINARY CHECKS Controls after transport After removing the packaging, make sure the pro-duct is complete and undamaged and that all ac-cessories are present.Do not use the appliance if it is visibly damag...

10 378 mm 594 mm 20 mm 398 mm 45 mm 45 mm 45 mm 45 mm 380 + 2 mm 850 mm Mi n 500 mm 545 mm Min. 200 cm 2 560 + 8 mm 45 m m 45 mm 45 0 + 2 m m M in 560 + 8 mm 500 mm 545 mm Min. 361 mm 528 mm 372 mm 15 mm BUILT-IN INSTALLATION Verify the minimum measurements required forcorrect installation of the ap...

12 USING THE APPLIANCEFOR THE FIRST TIME • Coffee has been used to factory test the ap-pliance and it is therefore completely normalfor there to be traces of coffee in the mill. • Customise water hardness as soon as pos-sible following the instructions in the "Settingwater hardness" section....

13 12. Press the OK icon (B9) again. The appliance begins delivering hot water and the message"PLEASE WAIT... " is displayed. When delivery stops, the appliance automa-tically displays the basic modes set again. N.B.! The appliance may request the ope- ration to be repeated a number of times...

NOTE 4: Introduce onlypre-ground coffee forespresso coffee machinesinto the funnel.NOTE 5: If more than onemeasure of pre-groundcoffee is used and the fun-nel clogs, push the coffeedown with a knife (fig. 21)then remove and clean thebrewing unit and machineas described in the "Clea- ning the bre...

insufficient, the appliance makes 2 cups thenstops making coffee. Fill the bean container andpress the icon (B14). Once the container hasbeen filled, the appliance makes the 2 remainingcups only to reach the required number of 4cups. If there is not enough water in the tank tocomplete the required f...

19 Important! When extracting the drip tray, the waste coffee container must always be em-ptied. Cleaning the drip tray Important! If the drip tray is not emptied the water might overflow. This could damage themachine. The drip tray is fitted with a level indi-cator (red) showing the level of water ...

21 Rinsing This function enables you to obtain hotter coffee. Proceed as follows:• When you turn the appliance on, if you wantto make a small cup of coffee (less than 60cc), preheat the cup by rinsing it with hotwater. • If on the other hand more than 2/3 minuteshave passed since the last coffee was...

23 • Press the OK icon (B9). "FILL TANK" is di-splayed. Fill the tank again with clean water. • The descale programme is now terminatedand the appliance is ready to make coffeeagain.NOTE: If descaling is interrupted before com-pletion, the process must be begun againfrom the beginning. Impor...

24 N.B.! If the appliance is not used for an extended period, place the main switch on theback of the appliance in the 0 position (A23). TECHNICAL SPECIFICATION Voltage: 220-240 V~ 50/60 Hz max. 10AAbsorbed power: 1350 W Pressure: 15 barsWater tank capacity: 1.8 litresSize LxHxD: 594x 378x398 mmWeig...

DISPLAYED MESSAGES DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY FILL TANK • The water tank is empty orpositioned incorrectly. • Fill the tank with waterand/or insert it correctly,pushing it as far as it willgo. GROUND TOO FINE ADJUSTMILL AND (alternating with)PRESS OK • The grinding is too fineand the co...

PROBLEM POSSIBLE CAUSE REMEDY TROUBLESHOOTING Below is a list of some of the possible malfunctions. If the problem cannot be resolved as described, contact Customer Services. The coffee is not hot • The cups were not pre-heated. • The brewing unit has coo-led down because 2/3 mi-nutes have elapsed s...