AEG L 98699 FL- Manuals

WARNING! Do not look directly into thebeam of the lamp. To replace the internal lamp,contact the service centre.Disconnect the mains plug fromthe mains socket before the re-placement of the internal lamp. INSTALLATION • The appliance is heavy, be careful when you move it. • Do not transport your app...

3. Discard the door catch. This pre-vents children or pets to be closedin the appliance. There is a risk of suffocation (only for front-loadingappliances). ENVIRONMENT CONCERNS PACKAGING MATERIALS Recycle the materials with the symbol . Put the packaging in applicable con-tainers to recycle it. ECOL...

TECHNICAL INFORMATION Dimensions Width / Height / Depth 600 / 850 / 600 mm Total depth 640 mm Electrical connection: VoltageOverall powerFuseFrequency 230 V 2200 W 10 A 50 Hz Level of protection against ingress of solid particlesand moisture ensured by the protective cover, exceptwhere the low volta...

PRODUCT DESCRIPTION 1 2 3 9 10 6 5 7 8 4 11 12 13 1 Worktop 2 Detergent dispenser 3 Control panel 4 Door handle 5 Internal lamp 6 Rating plate 7 Drain pump 8 Feet for the appliance level 9 Water drain hose 10 Water inlet hose 11 Mains cable 12 Transit bolts 13 Feet for the appliance level INTERIOR A...

CONTROL PANEL 1 2 3 4 5 6 7 8 9 10 11 12 1 Auto Off button 2 Programme knob 3 Display 4 Steam touch button 5 Memory touch buttons 6 Start/Pause touch button 7 Delay start touch button 8 Time save touch button 9 Extra rinse touch button 10 Option touch button 11 Spin reduction touch button 12 Tempera...

DISPLAY 3 A B C D E F G H I J A The text bar:• Guides you in the use of the appliance.• Shows the programme status and phase.• Shows alarm messages. Refer to 'Troubleshooting' . The symbols appear on the display when the related phase or function is set. B Child lock C Door lockedYou cannot open the...

• The time of delay – When you set the delayed start the time of the programme end in- creases by steps of 30 minutes till 10 hours and by steps of onehour till 20 hours. • The end of the programme The display shows a zero. E This part comes on only if the door is open - Refer to 'Loading the laun-d...

PREWASH Use this function for heavy soil.The appliance adds a prewash phase tothe main wash.The programme duration increases. SOAK Use this function for heavy soil.The appliance soaks the laundry at30°C for about half an hour before towash. SPIN BUTTON 11 Touch button 11 to: • Decrease the maximum s...

WASHING PROGRAMMES Programme Temperature Type of loadWeight of load Programmedescription Functions Cottons 95° - Cold White and col-oured cottonwith heavy levelof soil.Maximum load 9kg WashRinsesLong spin Spin Reduc-tionRinse HoldStains 1) Prewash 2) SoakExtra rinseTime save 3) Extra Silent 95° - Co...

Programme Temperature Type of loadWeight of load Programmedescription Functions Wool / Silk 40° - ColdRinsesShort spin Machine washa-ble wool as wellas for hand wash-able woollensand delicate fab-rics with «handwashing» caresymbol.Maximum load 2kg WashRinsesShort spin Spin Reduc-tionRinse Hold Duvet...

Programme Temperature Type of loadWeight of load Programmedescription Functions 20 Min. - 3kg 40° or 30° Quick wash ofsport items orcotton and syn-thetic items,lightly soiled orworn once.Maximum load 3kg WashRinsesShort spin Spin Reduc-tion Super Eco 0° Mixed fabrics(cotton and syn-thetic items) 8) ...

Steam - Anticrease 2) This programme helps to dew-rinkle the laundry. Cotton and synthetic items. up to1,5 Kg Steam can be used for dried, washed or worn once laundry. These pro-grammes can reduce creases and odours and make your laundry moresmooth.Do not use any detergent. If necessary, remove stai...

BEFORE FIRST USE 1. To activate the drain system, put 2litre of water in the main wash com-partment of the detergent dispens-er. 2. Put a small quantity of detergent inthe main wash compartment of thedetergent dispenser. Set and starta programme for cotton at thehighest temperature without laun-dry....

4. The display shows the default tem-perature and spin. If it is necessary,touch button 12 and button 11 to change the water temperature andthe spin speed. 5. If it is necessary, touch the otherbuttons to add some functions or to set a delayed start. The displayshows the symbol of the set func-tion ...

USING THE DETERGENT AND ADDITIVES The detergent compartment for the prewash phase and the soakprogramme.Add the detergent for prewash and soak before the start of theprogramme. The detergent compartment for the washing phase.If you use a liquid detergent, put it immediately before you startthe progr...

SET THE DELAY START 1. Touch button 7 again and again to set the desired delayed start.The display shows the expectedend of the programme 2. Touch button 6 , the appliance starts the countdown of the delaystart.When the countdown is comple-ted, the programme starts auto-matically. Before you touch b...

If you deactivate the appliance,it is necessary to set the pro-gramme again. AT THE END OF PROGRAMME 1. The appliance stops automatically. 2. The acoustic signals operate, if it isactive. 3. In the display goes on and the message tells you that the pro-gramme is completed. 4. The indicator of button...

HELPFUL HINTS AND TIPS THE LAUNDRY LOAD • Divide the laundry in: white, col- oured, synthetics, delicates and wool. • Obey the washing instructions that are on the laundry care labels. • Do not wash together white and col- oured items. • Some coloured items can discolour with the first wash. We reco...

Water hardness table Level Type Water hardness °dH °T.H. mmol/l Clarke 1 soft 0-7 0-15 0-1.5 0-9 2 medium 8-14 16-25 1.6-2.5 10-16 3 hard 15-21 26-37 2.6-3.7 17-25 4 very hard > 21 > 37 >3.7 >25 ENGLISH 25 www.devicemanuals.eu

CARE AND CLEANING WARNING! Disconnect the appliance from themains supply before you clean it. DESCALING The water we use contains limescale. Ifit becomes necessary, use a water soft-ener to remove limescales.Use a special product made for wash-ing machines. Obey the instructionsthat you find on the ...

DETERGENT DISPENSER To clean the dispenser: 1 2 1. Press the lever. 2. Pull the dispenser out. 3. Remove the top part of the liquidadditive compartment. 4. Clean all the parts with water. 5. Clean the dispenser recess with abrush. 6. Put back the dispenser in the re-cess. DRAIN PUMP Regularly examin...

To clean the drain pump: 1. Open the drain pump door. 2. Pull the flap out to remove it. 3. Put a container below the recess ofthe drain pump to collect the waterthat flows out. 4. Press the two levers and pull for-ward the drainage duct to let thewater flow out. 1 2 5. When the container is full of...

1 2 9. Clean the filter under the water tapand put it back in the pump intothe special guides. 10. Make sure that you tighten correct-ly the filter to prevent leakages. 11. Put the flap back and close thedrain pump door. THE INLET HOSE FILTER ANDTHE VALVE FILTER It could be necessary to clean the fi...

When you drain the water with theemergency drain procedure, you mustactivate again the drain system: 1. Put 2 litres of water in the mainwash compartment of the deter-gent dispenser. 2. Start the programme to drain thewater. FROST PRECAUTIONS If the appliance is installed in an areawhere the tempera...

TROUBLESHOOTING The start of the appliance does not oc-cur or it stops during operation.Try to find a solution to the problembefore you contact the service centre(refer to the table). With some problems, the acousticsignals operate and the displayshows an alarm message. WARNING! Deactivate the appli...

PROBLEM WITHOUT ALARM MESSAGE Problem Possible cause Possible solution The appliancedoes not drainthe water. A washing programmewithout the drain phaseis set. Set the drain programme. The function Rinse Holdis on. Set the drain programme. The spin phasedoes not operate. The spin phase is off. Set th...

Problem Possible cause Possible solution You did not remove thepackaging and/or thetransit bolts. Remove the packaging and/orthe transit bolts. Refer to 'Instal-lation'. The load is very small. Add more laundry in the drum. The appliance fillswith water anddrain immediate-ly. The end of the drainhos...

INSTALLATION UNPACKING 1. Use the gloves. Remove the exter-nal film. If necessary, use a cutter. 2. Remove the cardboard top. 3. Remove the polystyrene packagingmaterials. 4. Remove the internal film. 5. Open the door. Remove the poly-styrene piece from the door sealand all the items from the drum. ...

14. Replace the plastic spacers withthe plastic caps. You can find thesecaps in the user manual bag. WARNING! Remove all the packaging andthe transit bolts before you in-stall the appliance. We recommend that you keepthe packaging and the transitbolts for when you move the ap-pliance. POSITIONING AN...

Installation on suspendedflooring Suspended wooden floors are particu-larly susceptible to vibration. To helpprevent vibration we recommend youplace a waterproof wood panel, at least 15 mm thick under the appliance, se-cured to at least 2 floor beams withscrews, the wood panel must extendbeyond the ...

Water-stop device A The inlet hose has a water stop device.This device prevents water leaks in thehose because of its natural ageing. Thered sector in the window «A» shows thisfault .If this occur, close the water tap andcontact the service centre to replacethe hose. WATER DRAINAGE There are differe...

• If the end of the drain hose is this (see the drawing), you can push it di-rectly into the stand pipe. Without the plastic hose guide. • To a sink spigot. Refer to the illustration. Put the drainhose in the spigot and tighten it witha clip. Make sure that the drain hosemakes a loop to prevent that...

PRODUCT DESCRIPTION 1 2 3 9 10 6 5 7 8 4 11 12 13 1 Worktop 2 Detergent dispenser 3 Control panel 4 Door handle 5 Internal lamp 6 Rating plate 7 Drain pump 8 Feet for the appliance level 9 Water drain hose 10 Water inlet hose 11 Mains cable 12 Transit bolts 13 Feet for the appliance level INTERIOR A...

CONTROL PANEL Wolle/Seide Koch/Bunt Extra Leise Pflegeleicht Leichtbügeln Feinwäsche Daunen Anti-Allergie Schleudern/ Pumpen Spülen Outdoor 20Min. - 3kg Super Eco Auffrischen Glätten Auto Off Memory 1 Memory 2 Dampf Start/Pause Zeit- vorwahl Zeit Sparen Extra Spülen Flecken/ Vor w. Temp. U/Min. Gewi...

DISPLAY 3 A B C D E F G H I J A The text bar:• Guides you in the use of the appliance.• Shows the programme status and phase.• Shows alarm messages. Refer to 'Troubleshooting' . The symbols appear on the display when the related phase or function is set. B Child lock C Door lockedYou cannot open the...

VORWÄSCHE Use this function for heavy soil.The appliance adds a prewash phase tothe main wash.The programme duration increases. EINWEICHEN Use this function for heavy soil.The appliance soaks the laundry at30°C for about half an hour before towash. SPIN BUTTON 11 Touch button 11 to: • Decrease the m...

WASHING PROGRAMMES Programme Temperature Type of loadWeight of load Programmedescription Functions Koch/Bunt 95° - Cold White and col-oured cottonwith heavy levelof soil.Maximum load 9kg WashRinsesLong spin SPIN REDUC-TIONSPÜLSTOPPFLECKEN 1) VORWÄ-SCHE 2) EINWEICHENEXTRA SPÜ-LENZEIT SPA-REN 3) Extra...

7) Press button to add rinses. With a low spin speed the appliance performs delicate rinses and a short spin. 8) Use a special detergent for very low temperature.9) Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended. S...

Standard programmes for theEnergy Label consumptionvalues The cotton 60 °C economy and cotton40 °C economy are the standard cottonprogrammes for normally soiled cottonlaundry. They are suitable to clean nor-mally soiled cotton laundry and they are the most efficient programmes interms of combined en...

ACTIVATING THE APPLIANCE AND SETTING A PROGRAMME For a correct operation of the weight sensor, activate the appliance andset the programme BEFORE you put the laundry in the drum. 1. Press button 1 to activate the ap- pliance. 2. Turn the programme knob ( 2 ) to the necessary programme or touchone of...

Make sure not to have the laundry outof the drum between the seal and thedoor. There is the risk of water leakageor damage laundry. USING THE DETERGENT AND ADDITIVES The detergent compartment for the prewash phase and the soakprogramme.Add the detergent for prewash and soak before the start of thepr...

Check the position of the flap 1. Pull out the detergent dispenseruntil it stops. 2. Press the lever down to remove thedispenser. 3. To use powder detergent, turn theflap up. 4. To use liquid detergent, turn theflap down. With the flap in the positionDOWN: – Do not use gelatinous or thick liquid det...

SET THE DELAY START 1. Touch button 7 again and again to set the desired delayed start.The display shows the expectedend of the programme 2. Touch button 6 , the appliance starts the countdown of the delaystart.When the countdown is comple-ted, the programme starts auto-matically. Before you touch b...

If you deactivate the appliance,it is necessary to set the pro-gramme again. AT THE END OF PROGRAMME 1. The appliance stops automatically. 2. The acoustic signals operate, if it isactive. 3. In the display goes on and the message tells you that the pro-gramme is completed. 4. The indicator of button...

HELPFUL HINTS AND TIPS THE LAUNDRY LOAD • Divide the laundry in: white, col- oured, synthetics, delicates and wool. • Obey the washing instructions that are on the laundry care labels. • Do not wash together white and col- oured items. • Some coloured items can discolour with the first wash. We reco...

Water hardness table Level Type Water hardness °dH °T.H. mmol/l Clarke 1 soft 0-7 0-15 0-1.5 0-9 2 medium 8-14 16-25 1.6-2.5 10-16 3 hard 15-21 26-37 2.6-3.7 17-25 4 very hard > 21 > 37 >3.7 >25 ENGLISH 25

CARE AND CLEANING WARNING! Disconnect the appliance from themains supply before you clean it. DESCALING The water we use contains limescale. Ifit becomes necessary, use a water soft-ener to remove limescales.Use a special product made for wash-ing machines. Obey the instructionsthat you find on the ...

DETERGENT DISPENSER To clean the dispenser: 1 2 1. Press the lever. 2. Pull the dispenser out. 3. Remove the top part of the liquidadditive compartment. 4. Clean all the parts with water. 5. Clean the dispenser recess with abrush. 6. Put back the dispenser in the re-cess. DRAIN PUMP Regularly examin...

To clean the drain pump: 1. Open the drain pump door. 2. Pull the flap out to remove it. 3. Put a container below the recess ofthe drain pump to collect the waterthat flows out. 4. Press the two levers and pull for-ward the drainage duct to let thewater flow out. 1 2 5. When the container is full of...

1 2 9. Clean the filter under the water tapand put it back in the pump intothe special guides. 10. Make sure that you tighten correct-ly the filter to prevent leakages. 11. Put the flap back and close thedrain pump door. THE INLET HOSE FILTER ANDTHE VALVE FILTER It could be necessary to clean the fi...

When you drain the water with theemergency drain procedure, you mustactivate again the drain system: 1. Put 2 litres of water in the mainwash compartment of the deter-gent dispenser. 2. Start the programme to drain thewater. FROST PRECAUTIONS If the appliance is installed in an areawhere the tempera...

TROUBLESHOOTING The start of the appliance does not oc-cur or it stops during operation.Try to find a solution to the problembefore you contact the service centre(refer to the table). With some problems, the acousticsignals operate and the displayshows an alarm message. WARNING! Deactivate the appli...

PROBLEM WITHOUT ALARM MESSAGE Problem Possible cause Possible solution The appliancedoes not drainthe water. A washing programmewithout the drain phaseis set. Set the drain programme. The function Rinse Holdis on. Set the drain programme. The spin phasedoes not operate. The spin phase is off. Set th...

INSTALLATION UNPACKING 1. Use the gloves. Remove the exter-nal film. If necessary, use a cutter. 2. Remove the cardboard top. 3. Remove the polystyrene packagingmaterials. 4. Remove the internal film. 5. Open the door. Remove the poly-styrene piece from the door sealand all the items from the drum. ...

14. Replace the plastic spacers withthe plastic caps. You can find thesecaps in the user manual bag. WARNING! Remove all the packaging andthe transit bolts before you in-stall the appliance. We recommend that you keepthe packaging and the transitbolts for when you move the ap-pliance. POSITIONING AN...

THE INLET HOSE 35 O 35 O 35 O 45 O 45 O 45 O • Connect the hose to the appliance. Turn the inlet hose only left or right.Loose the ring nut to set it in the cor-rect position. • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are noleaks from the cou...

With the plastic hose guide. • On the edge of a sink.• Make sure that the plastic guide can- not move when the appliance drains.Attach the guide to the water tap orthe wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly intoa drain pipe at a height of not lessthan 60 cm and n...