Page 3 - CONTENTS
CONTENTS 4 Safety information 7 Installation 12 Product description 12 Operation 15 Helpful hints and tips 16 Care and cleaning 18 What to do if… 19 Technical data 20 Environment concerns The following symbols are used in this user manual: Important information concerning your personal safety and in...
Page 4 - General safety; do not play with the appliance.; Use; invalidate the guarantee.
SAFETY INFORMATION WARNING! These instructions are only valid in the countries whose symbols appear on this booklet's cover. For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you m...
Page 5 - Installation
• The cookware must not enter the control zone.• Make sure that the cookware does not protrude over the edges of the cooking surface and that it is centrally positioned on the rings in order to avoid safety risks. • Do not use unstable cookware or cookware with damaged bottom. There is a risk of til...
Page 6 - Disposal of the appliance
• Before installation, make sure that the local supply conditions (gas type and pressure) agree with the adjustment of appliance. The adjustment conditions for the appliance are on the rating plate, which you can find near the gas supply pipe. • This appliance is not connected to a combustion produc...
Page 7 - INSTALLATION; Important safety requirements; Gas Connection
INSTALLATION WARNING! The following instructions about installation, connection and maintenance must be carried out by qualified personnel in compliance with standards and local regulations in force. Important safety requirements This hob must be installed in accordance with the Gas Safety (Installa...
Page 8 - Injectors replacement
1 2 3 1 End of shaft with nut 2 Washer 3 Elbow Connection to the gas supply should be with either rigid or semi - rigid pipe, i.e. steel or cop- per. The connection should be suitable for connecting to R 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thoro...
Page 9 - The appliance must be earthed.
Adjustment of minimum level To adjust the minimum level of the burners:1. Light the burner. 2. Turn the knob on the minimum position. 3. Remove the knob. 4. With a thin screwdriver, adjust the by - pass screw position. 1 1 The by - pass screw – If you change from natural gas 20 mbar to liquid gas, f...
Page 12 - PRODUCT DESCRIPTION; Cooking surface layout; OPERATION; Ignition of the burner
Kitchen unit with oven The hob recess dimensions must obey the indication and the kitchen unit must be equipped with vents to let a continuous supply of air. The electrical connection of the hob and the oven must be installed separately for safety reasons and to let easy remove oven from the unit. 5...
Page 15 - HELPFUL HINTS AND TIPS; Energy savings; Do not use cooking vessels on the hotplate that overlap its edges.; Helpful hints and tips
When you install the grate of the Triple Crown burner afterwards, align the hollow part of the grate with the reference on the plate attached to the glass. CAUTION! Be very careful when you put the pan supports back on their position. There is a risk of scratching the glass hob top. HELPFUL HINTS AN...
Page 16 - Information on acrylamides; CARE AND CLEANING
WARNING! Pots must not enter the control zone. Flame will heat up the control zone. Do not put the same pan on two burners. WARNING! Make sure pot handles do not protrude over the front edge of the cooktop and that pots are centrally positioned on the rings in order to achieve maximum stability and ...
Page 17 - Cleaning of the spark plug
• The pan supports are not dishwasher proof; they must be washed by hand . • When you wash the pan supports by hand, take care when you dry them as the enamel- ling process occasionally leaves rough edges. If necessary, remove stubborn stains using a paste cleaner. • Make sure you position the pan s...
Page 18 - WHAT TO DO IF...; free of charge, even during the warranty period.; Labels supplied with the accessories bag; Stick the adhesive labels as indicated below:
WHAT TO DO IF… Problem Possible cause Remedy There is no spark when lighting the gas • There is no electrical supply • Make sure that the unit is connected and the electrical supply is switched on. • Control the fuse. If the fuse is released more than one time, refer to a qualified electrician. • Bu...
Page 19 - Stick it on Guarantee Card and send this part; TECHNICAL DATA; Technical data
MOD.PROD.NO.SER.NODATA MOD.PROD.NO.SER.NODATA MODEL MODEL MOD. PROD.NO. SER.NO. 03 ITMADE IN ITALY TYPE 230V-50Hz IP20 0049 1 2 3 1 Stick it on Guarantee Card and send this part 2 Stick it on Guarantee Card and keep this part 3 Stick it on instruction booklet These data are necessary to help you qui...
Page 20 - ENVIRONMENT CONCERNS; you purchased the product.
Electric supply: 230 V ~ 50 Hz 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse Category: II2H3+ Gas connection: R 1/2" Gas supply: G20 (2H) 20 mbar Appliance class: 3 By - pass diameters Burner Ø By - pass in 1/100 mm Auxiliary 28 Semi - rapid 32 Triple Crown 56...
Page 21 - Packaging material
Packaging material The packaging materials are friendly to the environment and can be recycled. The plastic components are identified by marking: >PE<,>PS<, etc. Discard the packaging materials as household waste at the waste disposal facilities in your municipality. 21