AEG DDLE Basis 13- Manuals

Page 5 - For users and contractors; description; s4EMPERATURESELECTOR; HEREISARISKOFSCALDINGATOUTLETTEMPERATURESINEXCESSOFa#; information; instructions

22 For users and contractors 1.1 Equipment description The instantaneous water heater DDLE Basis heats water as it ﬂows through the equipment. You can adjust the DHW outlet temperature anywhere between approx. 30 °C and approx. 60 °C via a temperature selector. From a ﬂow rate of approx. 3 l/min onw...

Page 6 - output; !VAILABLETEMPERATUREEGFOR; Recommended settings when using a thermostatic valve

23 For users and contractors 1.5 DHW output Subject to season, the following maximum mixed water or draw-off capacities result for different cold water temperatures (see Table 1): ϑ 1 = Cold water inlet temperature ϑ 2 = Mixed water temperature ϑ 3 = Outlet temperature. !VAILABLETEMPERATUREEGFOR Sho...

Page 7 - EQUIPMENTBACKINTOUSE; Instructions and regulations; For contractors

24 Only trained and authorised experts must install the device and make the electrical connection under full observance of these installation instructions. 2.1 Equipment layout A - O 1 Temperature selector 17 Flow sensor 2 Equipment cap 18 Temperature selector plug “set T” 3 Base, back panel 19 Type...

Page 8 - Water installation

25 ! For contractors s /BSERVEALLREGULATIONSOFYOURLOCALWATERANDELECTRICITYSUPPLYCOMPANIESs /BSERVETHETYPEPLATE ( A 19). s 3EE3PECIlCATION 4HESPECIlCELECTRICALRESISTANTOFTHEWATERUSEDMUSTNOTFALLBELOWTHATSTATEDONTHETYPEPLATE)NALINKEDWATERNETWORKOBSERVETHELOWESTELECTRICALWATERRESISTANCESEE!PPLICATIONARE...

Page 9 - Re-plug the coding card; Important information; installation; for contractors

26 For contractors 3.1 General installation information At the factory, the device is prepared for a power connection from the top from an installation below the plaster (see Fig. C - I ): s 4HEDEVICEISSUITABLEFORABOVEORUNDERSINKINSTALLATION C . s 7ATERCONNECTIONTHREADEDlTTINGSBELOWTHEPLASTERs 0OWER...

Page 10 - supply; Completing the installation; green fl ashing - equipment is supplied with mains power

27 s Never replace the pressure limiter when using a thermostatic valve. s Never use the shut-off valve in the cold water supply (23) to reduce the ﬂ ow rate. 3.7 Power supply s #ONNECTTHEPOWERCABLETOTHETERMINALSTRIPSEEWIRINGDIAGRAM I ). 1 heating system 2 High limit safety cut-out 3 Safety pressure...

Page 11 - LEASENOTE; HEDEVICECAPNEEDSTOTHEPREPAREDTORTHISINSTALLATION; Alternative installation methods

28 !LTERNATIVEINSTALLATIONMETHODSARESHOWNINlGURES J O 4.1 Power supply – unﬁnished walls - below K a Push the cable grommet (4) over the power cable. b Break out the cable grommet knock-out in the back panel. c Move the terminal strip from the top to the bottom; for this, undo the screw and reﬁt it ...

Page 12 - Specification and application areas; areas

29 Table 3 5. Speciﬁcation and application areas for contractors 5.1 Speciﬁcation (The details on the type plate apply) 5.2 Application areas Speciﬁc electrical resistance and speciﬁc electrical conductivity Table 4 For contractors Details as application ranges for different reference temperatures s...

Page 13 - by the user; by the contractor

30 Display options LED diagnostic “trafﬁc lights” red illuminates in case of faults yellow illuminates when the equipment is heating water green ﬂashing: the device is supplied with power Fault / Diagnostic “trafﬁc light” display* Cause Remedy Flow rate too low Shower head/perlators scaled up Contam...

Page 14 - s $IRECTTAPINSTANTANEOUSWATERHEATERS; accessories

31 For contractors s $IRECTTAPINSTANTANEOUSWATERHEATERS ADEo 70 WD - mono-lever mixer tap with changeover bath/hand shower Part no. 18 39 34 s )NSTALLATIONACCESSORIES Pipe assembly undersink installation UT 104 Part no. 18 44 21 Water connections with 12 mm compression ﬁttings s 5NIVERSALMOUNTINGFRA...

Page 15 - Customer service and warranty

32 Customer service and warranty For guarantees please refer to the respective terms and conditions of supply for your country. ! The installation, electrical connection and first operation of this appliance should be carried out by a qualified installer. ! The company does not accept liability for ...

Page 16 - Environment and recycling

33 Environment and recycling Recycling of obselete appliances Appliances with this label must not be disposed off with the general waste. They must be collected separately and disposed off according to local regulations. 10. Environment and recycling

A 28 1474-35066-090 1 Vertriebszentrale EHT Haustechnik GmbH Markenvertrieb AEG Gutenstetter Straße 1090449 Nü[email protected] www.aeg-haustechnik.deTel. 0 18 03 / 91 13 23 Fax 09 11 / 96 56 - 44 4 Kundendienstzentrale Holzminden Fürstenberger Str. 7737603 Holzminden Briefanschrift37601...