AEG AREK1 2 - Manuals

AEG AREK1 2 – User Manual in PDF format online.

Manuals:

User Manual

User Manual AEG AREK1 2

Summary

Page 2 - Contents

--------------------------------------------------------------------------------2/18-------------------------------------------------------------------------------- Contents 1 INTRODUCTION ............................................................................................................ 4 ...

Page 3 - 001 by AEG Identifikationssysteme GmbH

--------------------------------------------------------------------------------3/18-------------------------------------------------------------------------------- 9 MODES OF OPERATING AND COMMANDS OF THE READER ................................... 15 9.1 Set of Commands ...............................

Page 4 - transponder; reader

--------------------------------------------------------------------------------4/18-------------------------------------------------------------------------------- 1 Introduction This document will describe the components of the reader system ARE K1 / PFB and the procedure how to do the set up of t...

Page 5 - Project Planning

--------------------------------------------------------------------------------5/18-------------------------------------------------------------------------------- The antenna must not be brought next to a metal surface. This could lead to a significant change of the properties of the antenna circu...

Page 7 - SAB connector

--------------------------------------------------------------------------------7/18-------------------------------------------------------------------------------- 5 Installation To get the specified reading performance it is necessary to do the installation carefully step by step as it is describe...

Page 9 - Mounting of the Power Supply Cable; The power supply cable must be mounted in following steps:; Put the cable through the cable; Final Assembly of the Cable Pipe

--------------------------------------------------------------------------------9/18-------------------------------------------------------------------------------- 3 4 5 1 6 Cable 7 5.3.3 Mounting of the Power Supply Cable The power supply cable must be mounted in following steps: • Prepare the SAB...

Page 10 - Plug in of the SAB Cab; Plug in the SAB cab to the connector at the bottom of the reader box (B).; Connection to the Power Supply; Use a power supply of 24V; Connection characteristics of the digital inputs

--------------------------------------------------------------------------------10/18-------------------------------------------------------------------------------- • Fasten nut (5) of the cable pipes with the right tool (17mm). • Do this carefully, to ensure the tightness of the protection class o...

Page 11 - Assembling of the Data Cable (Profibus Network); Profibus

--------------------------------------------------------------------------------11/18-------------------------------------------------------------------------------- 3 4 5 1 6 Cable 7 8 5.3.9 Assembling of the Data Cable (Profibus Network) The connection from the ARE K1 / PFB to the master PLC is ma...

Page 12 - ANT

--------------------------------------------------------------------------------12/18-------------------------------------------------------------------------------- 5.3.10 Plug in of the Profibus SAB Cabs Attention! Before plugging the Profibus SAB cabs to the connectors of the reader, make sure th...

Page 13 - Make full cabelling due to Figure 2-1

--------------------------------------------------------------------------------13/18-------------------------------------------------------------------------------- 6.1 Operation at the End of a Network Line If an ARE K1/PFB is used at the end of a network line, the termination has to be activated ...

Page 14 - Indicators; Integration into the Profibus Network

--------------------------------------------------------------------------------14/18-------------------------------------------------------------------------------- 7.1 Indicators The device has 9 indicators. OP ANT READ NoREAD ERR Tx RX BusFail Run Figure 7-1: Position of all LED Indicators Their ...

Page 15 - function

--------------------------------------------------------------------------------15/18-------------------------------------------------------------------------------- 8.1 Profibus Slave: Configuration and Parametrization The ARE K1 / PFB has one configuration only. Only the seven standard Profibus pa...

Page 16 - Operating mode 2 - Reading Triggered by the PLC

--------------------------------------------------------------------------------16/18-------------------------------------------------------------------------------- com-mand-code function valid para- meter values default-values ALGO type of transponder 1, 2 1 (trovan read only) NID number of identi...

Page 17 - Never mount or place the antenna on extended metal parts.; FCC Information

--------------------------------------------------------------------------------17/18-------------------------------------------------------------------------------- Caution ! Never mount or place the antenna on extended metal parts. Do not bring another antenna very near to the operated antenna (se...

Page 18 - Documentation, References; Set of Commands for ARE K1; Contacts

--------------------------------------------------------------------------------18/18-------------------------------------------------------------------------------- 12 Documentation, References [1] : Manual: Set of Commands for ARE K1 Specifies all commands, parameters, transfer protocol, error cod...