AEG 79852G-A- Manuals

6 Hob burners To light a burner: z Push in the relevant control knob and turn it to maximum position. z Upon ignition, keep the knob pushed down about 5 seconds . This will allow the "thermocouple" (fig. 1 - letter D) to be heated and the safety device to be switched off, otherwise the gas s...

7 Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easilythan if it is left to cool. The Hob Top Regularly wipe over the hob top us...

8 Something Not Working? If the hob is not working correctly, please carry out the following checks before contactingyour local Service Force Centre. SYMPTOM „ There is no spark when lighting the gas „ The gas ring burns unevenly SOLUTION ‹ Check that the unit is plugged in and the electrical supply...

10 Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereofis proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair orreplace the same FREE O...

11 Instructions for the Installer Engineers technical data B U R N E R ULTRA-RAPID SEMI-RAPID A U X I L I A R Y (triple crown) ( m e d i u m ) (small) POSITION M A X M I N M A X M I N M A X M I N NOMINAL THERMALPOWER (kW) 3.8 1.20 1.9 0.45 1.0 0.33 NOMINAL FLOWRATE (m 3 /h) 0.362 0.114 0.181 0.043 0...

12 700 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 700 mm 400 mm 100 mm 400 mm 50 mm 50 mm 55 mm CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE FO 2028* FO 2027* Important safety requirements This hob must ...

13 Installation Important This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a CORGI registered installer. The manufacturer will not accept liability, should the above instructions or any of theother safety instructions in...

14 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heatresistant board below the base of the hob on the underside of the work surface.It is also ...

15 ON/OFF SWITCH FLEXOUTLET ON/OFF SWITCH FLEXOUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arrangements must be taken indesigning the furniture unit, in order to avoidany contact with the bottom of the hob whichcan be heated when it is operated. Therecommended solution is...

16 Fitting the hob to the worktop Before fitting the hob into the cut out, an adhesive seal must be fitted to the undersideoutside edge of the hob. It is essential that no gaps are left in this seal in order to preventspillage near the hob seeping into the cabinet below. 1) Remove the pan supports, ...

17 Electrical connections Any electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accordance with the current regulations.THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.Th...

18 Permanent Connection In the case of a permanent connection, it is necessary that you install a double poleswitch between the hob and the electricity supply (mains), with a minimum gap of 3 mm.between the switch contacts and of a type suitable for the required load in compliance withthe current el...

19 Fault Finding Preliminary Electrical Systems Check START Isolate applianceand carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supplyshould now besatisfactory. Carry out: D: Resistance to Earth check. Inlet wiringfaulty.Rectify anyfault. Isolat...

21 Check gas supply atburner Ignition System / Gas Ignition YES Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fitting ofburners Check position of theelectrode Check by pass simmeradjusted...

22 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite.2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several t...

23 Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can beconverted for use with butane or propane gas providing the correct injectors are fitted andthe gas rate is adjusted to suit. Method 1) Ensure that the gas taps are in the 'OFF...