AEG 68001K- Manuals

AEG 68001K– User Manual in PDF format online.

Manuals:

User Manual

User Manual AEG 68001K

Summary

Page 3 - Robbantott ábra szám: NDGTMG4029

- 2 - © Electrolux Robbantott ábra szám: NDGTMG4029 N00002079216 Mátrix PNC ELC Gyárt. Idő Modell A 949592498 00 20051219 78001KF-MN 69F Poz. Anyagszám Mátrix Megnevezés 001 3307266217 A Üveglap kerettel,69F 012 3305879201 A Indukció,főzőlap,D210 093 3305623005 A Felszerelés,erőegység 094 3305623021...

Page 4 - Operative Equipment Overview

Page 7 - current

2 599 519 523 EN DGS-TDS 21.04.08 1 General Information These instructions serve the repairing of autarkic cooking hobs and cooking hobs in combination with an oven with 3 or 4 inductions cooking zones respectively of the type E.G.O.. Also includes hobs with 2 induction zones (Domino, Mixed, Mixed g...

Page 9 - Appliance not functioning at all, cannot be switched on; Display

4 599 519 523 EN DGS-TDS 21.04.08 2 Alarm Symptoms 2.1 Appliance not functioning at all, cannot be switched on References e.g. (1) refer to the illustrations in Chapter 2.8 Alarm Symptom Cooking Hob Display Possible Alarm Cause Alarm Remedying House fuse triggered None Incorrect connection at the po...

Page 11 - Alarm Remedying; Inspecting the contacts on the

6 599 519 523 EN DGS-TDS 21.04.08 2.3 Alarm message "E“ When the appliance is switched on, "E“ / „xx“ Alarm Number is displayed in the timer display. With Frontline the display of the front zone indicates the error number when switching on. The affected zones are subsequently displayed with ...

Page 14 - Electric heating element relay instructions; Special error images for the cooker/hob combination

9 599 519 523 EN DGS-TDS 21.04.08 2.5.1 Electric heating element relay instructions • Refer to the wiring diagram xxx. The electric heating element is pulsed on relay board HOC2000 in the cooker. • Phase commutation with the cooker/hob combination, refer to Chapter 2.6, special error images for the ...

Page 16 - check 5V DC Pin 1+3 on

11 599 519 523 EN DGS-TDS 21.04.08 2.6.2 Cooking zone at the cooker okay, no display at the hob or no output. Alarm symptoms Display Possible Alarm Cause Alarm Remedying The diplay in the hob does not illuminate when voltage is connected. Cooker display okay. But: no cooking stage display at the hob...

Page 17 - display

12 599 519 523 EN DGS-TDS 21.04.08 Display in the hob 4 hobs dep. In comb. With cooker external user Interface 2.7 Unknown display For details, refer to the cooking field instruction manual Symbol Comment „ . “ Intermediate cooking levels („4.“) „ - “ Induction – zone switched off because of over te...

Page 18 - Terminal

13 599 519 523 EN DGS-TDS 21.04.08 2.8 Control Point Illustrations Air -inlet Min. 20mm Min. 5 mm Oven Remark: if there is no ventilation gap in the front it’s still possible to operate the hob. Only with longer useage ( >15 min. ) the performance will drop. For Mixed hob this is e.g. – 20%, for ...

Page 19 - Images control point for 2 zones / Mixed Induction

14 599 519 523 EN DGS-TDS 21.04.08 2.9 Images control point for 2 zones / Mixed Induction Attention: mains connection for Domino is directly on filter pcb. (2) (1) Domino (1) (3) (5) (6) (3) (7)

Page 20 - Testing Power Component

15 599 519 523 EN DGS-TDS 21.04.08 3 Testing Power Component 1. When alarm messages and disabled zones exist ("E“ in cooking phase display), please make a note of the power component which is affected. 2. (7) Check whether the lead from the filter board is connected, also check the bus lines (6)...

Page 21 - Pot Detection Information

16 599 519 523 EN DGS-TDS 21.04.08 4 Pot Detection Information Suitable pot materials: • Steel enamel • Stainless steel (with magnet. bottom) • Aluminium (with magnet. bottom) • Cast iron Unsuitable materials: • Aluminium ( Æ too much power) • Copper • Stainless steel (not magnetic) • Glass • Cerami...

Page 22 - Touch Control Autarkic Cooking Hobs Information

17 599 519 523 EN DGS-TDS 21.04.08 5 Touch Control Autarkic Cooking Hobs Information • The Touch Control works on the basis of the infrared principle, i.e. a signal is transmitted with a transmitter which is then reflected by the finger and received once more. 5.1 Instructions on the operation / pos...

Page 23 - Press the timer selection key; Service Mode “s”; Product history; Change from automatic boost to manual boost

18 599 519 523 EN DGS-TDS 21.04.08 5.2 Demo mode / Self test (Service mode) / Alarm Menu To enter the self-test/Demo mode, the following sequence of buttons must be pressed: 1. Hob is off. Press main switch continuously until display is going off (without beep). 2. Press the "+" and " -&...

Page 24 - Frontline self-sufficient hobs; Special references disassembly/assembly in case of a service:; (33) clamp bradings into the locking clips of the right carrier.

19 599 519 523 EN DGS-TDS 21.04.08 5.3.2 Error appliance can not be operated, display indicates "0" This error has been disappeared after a reset. For that there were 2 fault reasons in the hardware and software, this was removed by SW Vers. 4.2 from Dec. 2004. 6 Frontline self-sufficient ho...

Page 26 - Then automatically the; software version; of the user interface is displayed,; Demo mode

21 599 519 523 EN DGS-TDS 21.04.08 3. Then automatically the software version of the user interface is displayed, for example „2“ „8“ = version 28 and all LEDs / Displays are ON for 10 Sec. There is no alarm history mode available. 4. Demo mode By pressing the button "A" / „P“ of one of the ...

SERVICE MANUAL © Electrolux Distriparts Fürther Straße 246D-90429 NürnbergGermany DGS-TDS-N Publ.-Nr.: 599 722 426 685 10.09 DE Ausgabe: Cookers New hob oven combination „Criss Cross“ COOKERS

Page 40 - Transport safety adhesive tape before repair

Service-Bulletin DGS-TDS-N © Electrolux13.02.06 599 525 778 E N Cookers Induction hobs „G4“ Problem description: If you do not stick the transport safety adhesive on the coil connection cover afterrepairs, the high-frequency magnetic field can lead to a temperature rise in the coilarea. The coil can...

Page 42 - Description

Service-Bulletin DGS-TDS-N © Electrolux14.02.07 599 528 416 Cooking appliances EN Scorch locations with plug connections Problem: Charred respectively burnt plugs/pin terminals with electronics and switches. Reason: Due to faulty crimpings or expanded plugs arise scorch locations within the area of ...

Page 43 - SERVICE BULLETIN; Revision Date

SERVICE BULLETIN EN Publication no. 599 70 81-16 Rev. 02 11/2008 PR NOT CONFIGURED ELECTRONIC BOARDS (Rev. 02) In the sections: - “Electrical equipment” in Washing machines, Washer-dryers, Dryers and Dishwashers spare part lists. - “Diffuser” or “Cooling Unit” in Refrigeration appliances. the “confi...

Page 44 - G4 induction module

Service-Bulletin DGS-TDS-N © Electrolux11.07.2008 599 708 219 E N Cookers Autark induction hob with „G4“ induction moduleSwitching of the output on and off with the selected power mode G4 induction module Problem description: The induction module switches the power on and off with the selected power...