AEG 61502G-M- Manuals

5 1. Hob Top2. Rapid Burner3. Semi-rapid Burners4. Auxiliary Burner5. Control knob for back right burner (semi-rapid)6. Control knob for back left burner (semi-rapid)7. Control knob for front left burner (rapid)8. Control knob for front right burner (auxiliary)9. Electric Ignition Push Button Descri...

6 Hob burners control knobs The symbols on the knobs mean that : there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners For easier lighting, proceed before putting a pan on the pan support. To light a burner:push the electric ignition push button which is...

8 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wr...

9 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM There is no spark when lighting the gas The gas ring burns unevenly SOLUTION Check that the unit is plugged in and the electrical supply ...

10 Service and Spare Parts When you contact the Service Centre, they will need the following information:1. Your name, address and post code.2. Your telephone number3. Clear and concise details of the fault4. The model and the serial number (see rating label on the back of this instruction booklet)5...

11 Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any partthereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretionrepair or replace the same FREE O...

12 OVERALL DIMENSIONS Width: 580 mmDepth: 500 mm CUT OUT DIMENSIONS Width: 550 mmDepth: 470 mm SUPPLY CONNECTIONS Gas: R 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply, 3 core flexible cable withnon rewireable plug fitted with a 3 amp cartridge fuse. HEAT INPUTRear Le...

14 Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use)Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic GasInstallation I.S. ...

16 A) End of shaft with nut B) Washer C) Elbow FO 0814 FO 0264 On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that thewasher is fitted between the components as shown in the diagram. Screw the parts togetherwithout using excessive force. It is important...

17 Cut Out Size The dimensions of the cut-out are given in the diagram. Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heatresistant board below the base of the hob on the underside of the work surface. It is also...

18 ON/OFF SWITCH FLEXOUTLET ON/OFF SWITCH FLEXOUTLET FO 0763 FO 0764 1 2 Building over a kitchen unit with door Proper arrangements must be taken indesigning the furniture unit, in order toavoid any contact with the bottom of thehob which can be heated when it isoperated. The recommended solution is...

19 Fitting the hob to the worktop Before fitting the hob into the cut out,a sealing gasket supplied with thehob must be fitted to the edge of thecut out. It is essential that no gapsare left in this seal in order to preventspillage near the hob seeping into thecabinet below. 1) Place the sealing gas...

20 Electrical connections Any electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. ...

21 Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switchbetween the hob and the electricity supply (mains), with a minimum gap of 3 mm betweenthe switch contacts and of a type suitable for the required load in compliance with thecurrent ele...

22 Fault Finding Preliminary Electrical Systems Check START Isolate applianceand carry out: A: Earth Continuity check. Has inlet fuse blown? Carry out: C: Polarity check. Electricity supplyshould now besatisfactory. Carry out: D: Resistance to Earth check. Inlet wiringfaulty.Rectify anyfault. Isolat...

24 Check gas supply atburner Ignition System / Gas Ignition YES Check plug top fuse andreplace if necessary Check polarity and earthcontinuity of supply point Check earth continuityof appliance Ignitor does not spark Check fittingof burners Check position of theelectrode Check by pass simmeradjusted...

25 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting.To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several t...

26 Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion from natural gas to LPG should only be undertakenby a competent person. It is important to note that this model is designed for use with natural gas but can be converted for usewith butane or propane gas providing the correct...