AEG 32514DG-W- Manuals

Page 2 - Child Safety; About Installation, Cleaning and Manteinance; Service; Environmental Information

22 { cables are not in contact with it and keep them far enough from the heated parts of this appliance. If the appliance is out of order, disconnect it from the electric supply. Child Safety This appliance has been designed to be operated by adults and children under supervision. Young children...

Page 3 - Contents; For the User

23 Contents This appliance complies with the following E.E.C. Directives: - 73/23 - 90/683 (Low Voltage Directive); - 89/336 (Electromagnetical Compatibility Directive); - 93/68 (General Directives) and subsequent modifications. For the User For the Installer Important Safety Information 21 Descript...

Page 6 - Cleaning and Maintenance; General cleaning; Ignition candle

26 Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. General cleaning Wash the enamelled components with warm soapy water. Never use abrasive cleaners Frequently wash the "caps" and the "crowns" with ho...

Page 7 - Something Not Working?; Instruction for the Installer

27 FF Something Not Working? ...The gas ring burns unevenly -Check the main jet is not blocked and the burner crown is clear of food particles. -Check the burner cap and crown have been replaced correctly, e.g. after cleaning. ...There is no spark when lighting the gas - Check that the unit is plugg...

Page 8 - Injectors marks; Technical Data

28 Injectors marks Technical Data Dimensions in mm: Overall dimensions H x W x D 8 x 290 x 510 Cut out dimensions W x D 270 x 490 Gas Burners Rating in Watt: Front auxiliary burner 1000 Back rapid burner 3000 Total burner rating in Watt 4000 Gas connection R 1/2 Setting Natural gas - 20 mbar Adjust...

Page 9 - Gas connection

29 Ramp with ending nut Adjustable connection Rigid or flexible gas pipe Fig. 5 Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not sq...

Page 10 - Adaptation to different types of gas

30 F F Fig. 6 FO 0392 Injectors replacement Remove the pan supports. Remove the burner's caps and crowns. With a socket spanner 7 unscrew and remove the injectors (Fig. 6), and replace them with the ones required for the type of gas in use (see Technical data). Reassemble the parts, followin...

Page 11 - Replacement of the voltage cable; Electrical Connection

31 F FO 0257 Abb. 8 The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the l...

Page 12 - Building In

32 These hobs can be inserted in a built-in kitchen unit whose depth is between 550 and 600 mm. The hobs dimensions are shown in the relevant diagram. The edge of the cut out must have a minimum distance from the rear wall of 55 mm. If there are side walls, or sides of the furniture unit near the ho...

Page 13 - Fitting the hob to the worktop; Possibilities for insertion

33 F Dichtung Fig.11 Fitting the hob to the worktop To install the hob, proceed as follows: 1) Remove the pan supports, the burners caps and crowns and turn the hob upside down, taking care the ignition candles are not damaged in this operation. 2) Place the sealing gasket (supplied with the hob) on...

Page 15 - Service and original spare parts

35 This machine, before leaving the factory, has been tested and studied by many experts and specialists, in order to give you the best results. Any repair work which needs to be carried out should be done with the utmost care and attention. For this reason we reccomend that for any problem you cont...