AEG 222D-M/GB- Manuals

Page 3 - Contents

3 Contents Introduction 4 Extraction mode 4 Recirculation mode 5 Electrical connections 6 Technical details 7 Installation 8 Safety warnings for kitchen unit installer 8 Wall unit mounting 1 0 Wall mounting 1 1 Hood operation 1 2 Safety warnings for user 1 3 Maintenance and care 1 4 Opening the grid...

Page 4 - Introduction; Extraction mode

4 2 Introduction Extraction mode ● The hood is supplied as an extractor unit and can also be used with a filtering function by fitting activated carbon filters (available as an accessory). ● The unit features two outlet holes, one of which A is located on the top of the unit while the other B is loc...

Page 6 - Electrical connection

6 Electrical connection 220-240 V - using fixed power supply line with plug. (The unit should only be connected up by an authorized electrician). Your appliance must be connected to fixed wiring via the use of a double pole swiched fused spur outlet with or without pilot lamp.We strongly recommend t...

Page 7 - Technical details

7 Technical details DimensionsHeight x Width x Depth (in cm) 13 x 59,9 x 51 Weight Net: 6,9 kg Gross: 7,8 kg Maximum absorbed power: 205 W Motor absorption 1 x 125 W Lighting: 2 x 40 W Length of the cable: 110 cm Fan powers (speed), speed in compliance with DIN 44971 Extraction mode Speed 1 115 m 3 ...

Page 8 - Installation; Safety warnings for kitchen unit installer

8 Installation Safety warnings for kitchen unit installer ● When used as an extractor unit, the hood must be fitted with a 120mm diameter hose. ● If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.- 610 899 0...

Page 10 - Wall unit mounting

10 Wall unit mounting ● Make the holes on the bottom of the cupboard, using the drilling template . ● From inside the cupboard, insert the 4 supplied screws and tighten them in the appropriate holes on the appliance. Fig. 4. 4

Page 11 - Wall mounting

11 Wall mounting ● Fix the drilling template to the wall. ● Make 3 Ø 8mm holes in the wall 2 at points I , 1 as desired at points L . ● Insert the three Ø 8mm expansion plugs into the wall. ● Insert 2 5x45 screws at points I but do not tighten them completely. ● Adjust the unit so that it is positio...

Page 12 - Hood Operation

12 Hood Operation ● The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated. The ...

Page 13 - Safety warnings for user

13 ● Never leave a cooking hob or ring on without a pot or pan on top of it, to avoid the possibility of excess heat damaging the unit. Gas, oil in particular should never be left uncovered. ● Special care should be taken when using deep fat fryers since the oil in them can overheat and burst into f...

Page 14 - Maintenance and care; Opening the grid

14 6 Maintenance and care ● The hood must always be disconnected from the mains power supply before beginning any maintenance work. Opening the grid ● Open the latch L and swing the grille downwards. Fig. 6. ● To remove the grid, pull it forwards from the right and release it. Grease filter ● The ...

Page 16 - Cleaning

16 Warning ● Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. Changing the light bulb ● Disconnect the unit from the mains power supply. ● Remove the grid. ● Replace the ol...

Page 18 - Service & Spare Parts

18 Service & Spare Parts If you require a service engineer or wish to purchase spare parts, contact your local AEG Service Center, by telephoning: 0990 929929 Help us to help you Please determine your type of enquiry before telephoning. When you contact us we need to know. 1. Your name, address ...