Adcom GTP-760 - Manuals

Video Aux Input: This input is electrically identical to the LD input described above and will accommodate a widevariety of audio/video sources. After selecting and connecting the source’s composite or S-Video output to the GTP-760’scorresponding “video aux” video input, connect the source’s left ch...

Tape Inputs and Outputs: These connections are designed for a cassette deckor any other audio recording device with line-levelanalog inputs and outputs. Follow these instructions: 1) Connect the recorder’s left channel analog audio output to the GTP-760’s white “tape in” jack.2) Connect the recorder...

23 S-Video Inputs and Outputs Note: This section assumes that you’ve elected to use S-Video sources and display devices and thatyou’ve set the GTP-760 for S-Video signal transfer by following the steps described in the boxed noteentitled Composite or S-Video? on page 9. When hooking up S-Video capab...

24 Video Processor On/Off Switch This switch controls a “video loop” that enables the GTP-760 to function with a separatevideo processor. For conventional home theater systems, make sure the “video processor on/off” switch is in the OFFposition. When using a separate video processor, place this swit...

27 5.1 Channel Inputs These are the multichannel analog inputs. Connect your DVD-Audio, SACD or other multichannel source as follows: 1) Connect the source’s “front left” output to the white-centered RCA input marked “front”.2) Connect the source’s “front right” output to the red-centered RCA input ...

29 AC Convenience Outlets (115VAC models) These outlets are for low-current source components only. They are notdesigned for power amplifiers. The single unswitched outlet is live whenever the GTP-760 is plugged into a live AC source. The twoswitched outlets are live only when the GTP-760 is fully o...

Remote Function Table This table supplements the information you’ve just read. Use it to quickly review button functions. Thecontroller’s capabilities are extensive and may be somewhat intimidating at first. However, you will soon findthat its logical button arrangement and programming capabilities ...

BUTTON FUNCTION Main CD Tuner All Others 0 Not programmable Track 10 Programmable Programmable + 10 Not programmable + 10 Programmable Programmable SHIFT Not programmable Call Presets 8 - 14 Programmable FM/AM Not programmable Repeat FM or AM select Programmable STEREO Stereo mode select Program/Mem...

Deleting (clearing) Individual Programmed Commands 1. Press the ADCOM remote’s source selector and select/play buttons simultaneously and hold until theorange status LED and the source selector button glow steadily. 2. Press the function button you wish to clear. The status LED will flash continuous...

m1 button is pressed IF main, DVD, dig. 1, or dig. 2 sources are active at the time you select that macro. If you’ve programmed a Group 2 macro, it will send out an identical command sequence whenever tuner, CD,VCR, or v. aux inputs are active. Programming Macro Initiator Buttons: 1. Press either th...

3.0 INITIAL SETUP What this section is all about . . . After connecting your home theater, you may elect to configure the GTP-760 to the specific speaker arrange-ment and dimensions of your system. The procedures described in this section demonstrate how to use theGTP-760’s on screen display to ente...

In a typical home theater system, the distance from each speaker to the listening position will bedifferent. The most common example: in many home theaters the center and rear speakers sit closerto the listener than the main speakers. In such a situation the sound emitted from the closer speakerswil...

3.4 CHANNEL BALANCE From the SETUP screen, select CHANNEL BALANCE with the or buttons and press select/play.You will see: CHANNEL BALANCE LEFT - + RIGHT - + CENTER - + REAR L - + REAR R - + SUB - + UNDO CHANGESDONE Each piece of home theater equipment operates differently. In the same system, amplif...

Second, the subwoofer trim appears in the CHANNEL BALANCE menu, but not during the operation of thenoise sequencer. Because the subwoofer operates at a limited frequency range and because the sound levelmeasurement is weighted, the noise sequencer method of channel trimming is often unreliable in se...

If you have chosen to use a mix of both Composite and S-Video sources, the VIDEO field of the INPUTSETTINGS menu is the place to set the mode. In the example from section 1.2, a composite VCR and an S-Video DVD are to be used. Select the VCR input of the GTP-760. The VIDEO field should show COMPOSIT...

Listening to “Preset” Stations 1) Select tuner and either FM or AM. 2) Press the appropriate preset button (or shift + the preset button for choices higherthan “preset 7”). 4.3 Room 2 Operation IntroductionThe GTP-760’s “Room 2” circuitry gives you the ability to simultaneously enjoy two different a...

Operating Room 2 From “Room 2” In addition to the front panel Room 2 controls, the GTP-760 provides an interface for controlling Room 2remotely. Such a connection is technically sophisticated and usually intended only for custominstallations. Please contact your ADCOM dealer or ADCOM directly for fu...

6.0 CARE, MAINTENANCE, and SERVICE CARING FOR YOUR GTP-760 ADCOM has taken great care to ensure your GTP-760 is as flawless in appearance as it is electronically. Thefront panel is a heavy gauge, high-grade aluminum extrusion carefully finished and anodized for durability. Thechassis, top cover, and...

10 Timber Lane Marlboro, NJ 07746 Tel: (732) 683-2356 Fax: (732) 683-9790 www.adcom.com (c) 2000 by ADCOM.All rights reserved. Printed in the USA GTP-760/v.1.0