A&D FS-6Ki - Manuals

A&D FS-6Ki – Manual in PDF format online.

Manuals:

Manual

Manual A&D FS-6Ki

Summary

Page 2 - This Manual and Marks

This Manual and Marks All safety messages are identified by the following, “WARNING” or “CAUTION”, of ANSI Z535.4 (American National Standard Institute: Product Safety Signs and Labels). The meanings are as follows: WARNING A potentially hazardous situation which, if not avoided, could result in dea...

Page 3 - Contents

1 Contents 1. COMPLIANCE ................................................................................................. 2 2. INTRODUCTION .............................................................................................. 3 3. UNPACKING ....................................................

Page 4 - NSF listed

2 1. COMPLIANCE Compliance with FCC rules Please note that this equipment generates, uses and can radiate radio frequency energy. This equipment has been tested and has been found to comply with the limits of a Class A computing device pursuant to Subpart J of Part 15 of FCC rules. These rules are...

Page 6 - -1. Precautions for Installing the Scale; Consider following conditions to get the most from your scale.; -2. Precautions for Operating the Scale

4 4. CAUTION 4-1. Precautions for Installing the Scale Ground the scale so that the user will not be subjected an electric shock. Do not handle the main power cord with wet hands. The AC plug is not water-resistant. Install it in an area where it does not get wet. Do not install the scale wh...

Page 7 - -1. Attaching a display pod to the display support column; Clamp

5 5. SETTING UP 5-1. Attaching a display pod to the display support column 1. Take out whole of the scale from the box taking care not to pull the load cell cable. 2. Remove 2 clamps and 2 M4x12 screws. 3. Attach the display pod to the display support column and tighten the M4x12 screws removed at s...

Page 13 - Note for the Legal for Trade Models

11 Note for the Legal for Trade Models The range for power-on zero is within ±10% of the weighing capacity around the calibrated zero point. The ZERO key will zero the scale if the weight is within ±2% of the weighing capacity around the power-on zero point. The ZERO annunciator turns on. When t...

Page 16 - Setting the target weight by sample; Setting the target weight by key; Setting the HI limit weight and LO limit weight

14 Setting the target weight by sample 1. Press the ZERO key to zero the weight display if necessary. 2. Place the sample on the weighing pan. The display shows the sample item’s weight. 3. Press the SAMPLE key. The sample weight flashes and the central part of analog display turns on. Press the O...

Page 19 - Storing a set of limits in memory

17 3. Press the ENT key to store the HI limit weight in memory. 4. The display shows 5tored for a few seconds and returns to weighing mode. 5. Press the LO key and the last LO limit weight entered will flash. 6. Enter the LO limit weight via the 10-key pad. If you hit the wrong key, press the C ke...

Page 20 - Recalling a set of limits from memory; rd

18 Recalling a set of limits from memory 1. Press the RECALL key. Then the display will show rd 00 . 2. Press the memory number, for example 3. If you stop to recall, press the C key, the scale returns to the weighing mode. 3. Press the ENT key to recall the data from the memory. 4. The display sh...

Page 21 - ANALOG SWEEP DISPLAY

19 9. ANALOG SWEEP DISPLAY The FS- i series has a 60 segments analog sweep display. The DISP. key switches its display mode. It is possible to specify the display mode that will be shown first when the power is switched on. See the Function F16. Use the analog sweep display with positive target ...

Page 22 - -2. Example of the analog sweep display; Simple weighing display mode

20 9-2. Example of the analog sweep display Simple weighing display mode FS-30K i / d=0.01 kg TARGET WEIGHT SETTING MODE (F07-1 or F07-2) Target weight = 15.00 kg. Net weight display (tare entered) FS-30K i / d=0.01 kg UPPER & LOWER LIMIT WEIGHT SETTING MODE (F07-0) Target weighing display mode ...

Page 24 - Cal

22 10. CALIBRATION This function adjusts the scale for accurate weighing. Calibrate the scale in the following cases. When the scale is first used. When the scale has bee moved. When the ambient environment has changed. For regular calibration. Loose the lock screws on the rear side of the d...

Page 25 - end

23 7. To calibrate with the different weight, change the displayed value using the 10-key pad. If you hit the wrong number, press the C key. The value returns to the capacity and enter again. 8. Place the calibration weight on the pan with the same value as displayed, and wait until the STABLE ann...

Page 26 - 1-1. The procedure for setting parameters

24 11. FUNCTIONS The scale has Function settings to expand your applications. The parameters set in the Function settings are maintained even if the power switched off. 11-1. The procedure for setting parameters 1. Turn the power off. 2. Press and hold the ZERO key and turn the power on via the ON/O...

Page 31 - GRAVITY ACCELERATION MAP; Values of gravity at various locations

29 13. GRAVITY ACCELERATION MAP Values of gravity at various locations Amsterdam 9.813 m/s 2 Manila 9.784 m/s 2 Athens 9.807 m/s 2 Melbourne 9.800 m/s 2 Auckland NZ 9.799 m/s 2 Mexico City 9.779 m/s 2 Bangkok 9.783 m/s 2 Milan 9.806 m/s 2 Birmingham 9.813 m/s 2 New York 9.802 m/s 2 Brussels 9.811 m/...

Page 32 - World map

Page 33 - MEMO