A&D 1WMPD4002313 - Manuals - manualsarea.com

Page 2 - This Manual and Marks

This Manual and Marks All safety messages are identified by the following, “WARNING” or “CAUTION”, of ANSI Z535.4 (American National Standard Institute: Product Safety Signs and Labels). The meanings are as follows: WARNING A potentially hazardous situation which, if not avoided, could result in dea...

Page 3 - Contents

1 Contents 1. COMPLIANCE ................................................................................................. 2 2. INTRODUCTION .............................................................................................. 3 3. UNPACKING ....................................................

Page 7 - INSTALLATION and PRECAUTIONS; -1. Precautions for Installing the Indicator; Read the section “CAUTION” in the instruction manual of the FS

5 4. INSTALLATION and PRECAUTIONS 4-1. Precautions for Installing the Indicator Ground the indicator so that the user will not be subjected an electric shock. Do not handle the main power cord with wet hands. The AC plug is not water-resistant. Install it in an area where it does not get wet. ...

Page 8 - -3. Verifying Load Cell Output and Input Sensitivity; Calculating formula:

6 Setscrew B Setscrew A 4. Solder the wires to the pin contacts of the connector. A 5 m or less load cell cable is recommended as the FS - D uses a 4 wire system (no remote sensing). 5. Reassemble the connector plug and tighten the setscrew A. 6. Move the load cell cable back and forth and around,...

Page 9 - FUNCTION PARAMETER SETTINGS

7 4-4. Setting Up the Indicator Connect the main power cord to an outlet that has an earth ground terminal. You may use the earth terminal on the rear side of the display to ground the indicator. If necessary, adjust the viewing angle of the display by loosening the 2 clamps, changing the angle ...

Page 10 - NAMES AND FUNCTIONS

8 5. NAMES AND FUNCTIONS No. NAMES FUNCTIONS / OPERATION WEIGHT DATA DISPLAY Indicates the weight data. WEIGHING UNIT INDICATOR Indicates the weighing unit in use. ANALOG WEIGHT DISPLAY Indicates zero to full scale or comparison limits and results. OVER RANGE INDICATORS Turns ON when the weight is o...

Page 12 - -1. The procedure for setting parameters; Cal

10 6. FUNCTION PARAMETER SETTINGS To design a platform scale, set the capacity, weighing unit and other functions according to the specifications of the scale. Normally, end users do not have to set these function parameters and these setting can be sealed together with the calibration switch. 6-1. ...

Page 15 - a weight; end

13 If you need ZERO calibration but do not need SPAN calibration, turn the power off to exit from the calibration procedure. 7. To calibrate with a different weight, change the displayed value using the 10-key pad. If you enter the wrong number, press the C key. The value returns to the capacity...

Page 16 - ADDITIONAL INFORMATION

14 8. AUTO-TARE FUNCTION The FS - D has an auto-tare function to be used with the comparator function enabled. If the weight value is within the OK range and stable for a preset time, then the indicator will automatically tare the weight and show zero. The Function “ f22 ” designates the timing to t...

Page 17 - Circuit diagram

15 9. ADDITIONAL INFORMATION This section describes the additional functions and corrections to the instruction manual of FS - i series (WM+PD4001332 and 1WMPD4001368) which are common to the FS - D. 9-1. F-Function list The following function settings are added (“ 11-2. Function list ” in WM+PD4001...

Page 18 - Data format; Examples of command and reply

16 The frame ground and the shield are connected internally and there is no difference between them in use. Data format Example of data Out of range “kg” (+) O L , + 9 9 9 9 9 9 9 9 _ k g C R L F Out of range “kg” (+) O L , + 9 9 9 9 . 9 9 9 _ k g C R L F The position of decimal point is different...

Page 20 - Overload error; Low battery; err

18 10. ERROR MESSAGES Overload error Warning to indicate that an object beyond the weighing capacity has been placed on the weighing pan. Remove the object from the weighing pan. Power-on error Warning to indicate that an object beyond the power-on zero range (50% of the weighing capacity or 10%) is...

Page 24 - A&D Instruments India Private Limited

3-23-14 Higashi-Ikebukuro, Toshima-ku, Tokyo 170-0013 JAPAN Telephone: [81] (3) 5391-6132 Fax: [81] (3) 5391-6148 A&D ENGINEERING, INC. 1756 Automation Parkway, San Jose, California 95131 U.S.A. Telephone: [1] (408) 263-5333 Fax: [1] (408)263-0119 A&D INSTRUMENTS LIMITED <UK Office> Un...