3M M150 - Manuals

6 M150 FPD Monitor Installation Guide CAUTION To avoid the risk of electric shock which may result in minor or moderate injury: The socket-outlet should be installed near the equipment and should be easily accessible. Use a power cable that is properly grounded. Always use the appropriate AC cord ce...

Overview 7 • To avoid ergonomic concerns: Do not install the monitor in a manner or location with awkward accessibility. Extended use may result in muscle, tendon, or fixed posture strains. It is recommended you take periodic breaks from continuous use. Service and Repair Indicators Do not attempt t...

8 M150 FPD Monitor Installation Guide • Technical Support Hot Line: 978-659-9200 • Technical Support Fax: 978-659-9400 • Toll Free: 1-866-407-6666 • Email: [email protected] 3M Touch Systems Worldwide Offices All offices can be reached through the website: http://www.3mtouch.com/. • United S...

C H A P T E R 1 Introduction to Flat Panel Displays The 3M Touch Systems product line of Flat Panel Display (FPD) touch monitors offers the M150 monitor for desktop and countertop applications with built-in multimedia options. Spine Adjustment Knob Yoke The newly redesigned M150 monitor features an ...

10 M150 FPD Monitor Installation Guide Capacitive and Resistive Options The monitor is available with 3M Touch System’s ClearTek® capacitive touch screen. Capacitive is the touch screen of choice for public access applications requiring high levels of durability and reliable performance 24 hours a d...

C H A P T E R 2 Setting Up Your M150 FPD Monitor This chapter describes how to set up and integrate your 3M Touch Systems M150 FPD monitor into a touch application. You need to complete the following tasks: • Unpack the components • Connect the video, touch screen, and power cables • Power on the mo...

12 M150 FPD Monitor Installation Guide Unpacking Your Touch Monitor Carefully unpack the carton and inspect the contents. Your M150 monitor includes the following cables and accessories: 15-pin video cable 9-pin RS-232 serial communication cable (or USB cable if applicable) AC/DC power supply (12V D...

Chapter 2 Setting Up Your M150 FPD Monitor 13 Figure 1 Disassembling the Yoke & Base for Arm Mounting Step 3 -- Remove the inner four screws holding the base to the FPD and gently remove the base. Step 2 -- Remove the bottom two screws holding the hinge cover in place. Remove the small hinge cov...

14 M150 FPD Monitor Installation Guide Access to the Video Controls The controls for adjusting the video display are located on the front of the M150 FPD monitor. These buttons let you display the on-screen menu and adjust the phase, image position, contrast, and brightness. Make sure you have unobs...

Chapter 2 Setting Up Your M150 FPD Monitor 15 Note: When the adjustment knob is horizontal it is locked; when it is in the vertical position it is unlocked. Always maintain adequate ventilation to protect the display from overheating and to ensure reliable and continued operation. Installing the Vid...

16 M150 FPD Monitor Installation Guide Using the Standard Controls for the Video Card In addition to the standard controls on the monitor, each video card has several controls that let you adjust the display settings. The software and driver for each video card is unique. In most cases, you adjust t...

Chapter 2 Setting Up Your M150 FPD Monitor 17 ID Tech MagTek all MiniMag™ readers all "mini" sized readers IDT 3331-02U IDT 3321-33 2180201 IDT 3331-12U IDT 3321-33PP 2180202 IDT 3331-23U IDT 3331-02 2180203 IDT 3331-33U IDT 3331-12 2180204 IDT 3321-02 IDT 3331-23 2180205 IDT 3321-02PP IDT 3...

18 M150 FPD Monitor Installation Guide 4. Plug the AC/DC power supply into the M150 FPD. Be sure to use the power supply included with the monitor. Figure 7 Identifying Your Monitor Connections Video Connection Microphone out Line In Touch Screen Power WARNING To avoid the risk of electric shock whi...

Chapter 2 Setting Up Your M150 FPD Monitor 19 Route all wiring and cabling away from heat sources and sharp metal edges to avoid damage. Also, keep the touch screen cable away from sources of electromagnetic and radio frequency interference. WARNING To avoid the risk of electric shock which could re...

20 M150 FPD Monitor Installation Guide Testing the M150 FPD Note: The M150 FPD has a power status light located on the front of the bezel. After connection, turn on the power switch located at the bottom of the front bezel. Before you test your touch monitor, make sure all cables are connected prope...

Chapter 2 Setting Up Your M150 FPD Monitor 21 Calibrating the Touch Screen After you connect your touch monitor and install TouchWare software, you must calibrate the touch screen. Calibration serves two purposes: • Sets the active area of the touch screen • Aligns the touch screen’s active area to ...

C H A P T E R 3 Video Display Options This chapter provides guidelines for adjusting the video display and using the monitor controls to adjust the image to your liking. Before you make any adjustments: • Be sure to adjust the controls in your normal lighting conditions. • Display a test image or pa...

24 M150 FPD Monitor Installation Guide Auto Config To perform an Auto Config, press the ◄ /left arrow key once then press SELECT. The Main Menu item Auto Config is used to adjust the configuration of the phase clock vertical and horizontal position automatically. A confirmation box is displayed to c...

Chapter 3 Video Display Options 25 Contrast Selecting the Contrast option will allow you to adjust the contrast of the display. Adjust the contrast using the ◄ /left and ► /right arrow buttons, and press SELECT to confirm the new setting. Color When you choose the Color option from the OSD, this wil...

26 M150 FPD Monitor Installation Guide You can use the Position option to center the image on the display manually. Use the ◄ / left and ► /right arrow buttons to scroll through the position menu. • H-Position is used to adjust the horizontal image position manually. • V-Position is used to adjust t...

Chapter 3 Video Display Options 27 Miscellaneous Menu The Miscellaneous Menu contains three options: Reset, OSD Position, and System info. • Reset is used to reload all factory default parameters. • OSD position is used to setup the OSD menu position – horizontal and vertical position is adjusted se...

C H A P T E R 4 Maintenance and Troubleshooting If you have a problem setting up or using your monitor, you may be able to solve it yourself. Before calling 3M Touch Systems, try the suggested actions that are appropriate to the problems you are experiencing with the monitor. You may also want to co...

30 M150 FPD Monitor Installation Guide • Apply the cleaner with a soft, lint-free cloth. Avoid using gritty cloths. • Always dampen the cloth and then clean the screen. Be sure to spray the cleaning liquid onto the cloth, not the screen, so that drips do not seep inside the display or stain the beze...

Chapter 4 Maintenance and Troubleshooting 31 Troubleshooting the Touch Screen If you are experiencing problems with the touch screen, check the following list of common installation errors. Table 2. Common Touch Screen Installation Issues Common Installation Issues Possible Solutions Touch screen do...

32 M150 FPD Monitor Installation Guide This equipment has been tested and found to comply within limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equip...

0.21" (5.5 mm) 0.39" (10 mm) Cut Line Front Edge of Base Drill 3 Mounting Holes Rear Edge ofBase Not Shown M150 Base Plate Mounting Template (Drawn actual size) 3M Touch Systems Proprietary Information Place this template on mounting surface and drill three holes as shown for mounting screws...