3M D-2400 - Manuals - manualsarea.com

Page 2 - FCC Information; This device must not cause harmful interference.; Trademarks

FCC Information This device complies with part 15 of the FCC rules. Operation is subject to thefollowing two conditions: • This device must not cause harmful interference. • This device must accept any interference received including interference hat may cause undesired operation.Changes or modifica...

Page 3 - Front Matter; Revision Record

3M Model D-2400 Front Matter i Revision Record Date Revision Reason For Change 5/00 01 Preliminary manual released. 6/00 02 Incorporated changes from Revision 01. 7/00 03 Incorporated changes from Revision 02. 7/00 04 Incorporated changes from Revision 03 7/00 A Released manual 8/00 B Incorporated c...

Page 4 - ii; Table of Contents

Front Matter 3M Model D-2400 ii Table of Contents System Components .................................................................................... 1 Component Placement ................................................................................ 3 Communications Controller ...................

Page 5 - Station Selectors; Important

3M Model D-2400 System Components 1 System Components The 3M™ Model D-2400 Convenience Store Intercom System consists of one of the following components: • Station Selectors • Call Stations • Communcations Controller Figure 1. Model D-2400 Convenience Store Intercom System Components Material Requir...

Page 6 - System Components; This page intentionally left blank.

System Components 3M Model D-2400 2 This page intentionally left blank.

Page 7 - Communications Controller; Figure 2. Suggested Communications Controller Placement

3M Model D-2400 Component Placement 3 Component Placement This section describes placement of the 3M™ Convenience Store Intercom System, Model D-2400, components: Communications Controller For proper system operation, locate the Communications Controller: 1. Near the conduit termination of the Call ...

Page 8 - Component Placement; Call Stations; Note; Figure 3. Suggested Call Station Placement; Figure 4. Suggested Selector Station Placement

Component Placement 3M Model D-2400 4 Call Stations For proper system operation, install the Call Stations in locations: 1. Chosen for ease of use. 2. At least 48 inches above the pavement. ü Note Local codes may dictate placement of call stations. Figure 3. Suggested Call Station Placement Station ...

Page 9 - Figure 5. Cable and Connection Requirements

3M Model D-2400 Wiring the System 5 Wiring the System Depending on distance use twisted pair, 14-22 AWG audio cable when wiring Convenience Store IntercomSystem, Model D-2400, components. Figure 5 shows an overview of the cable types and number of connectorsrequired for each unit. Table 1 shows wire...

Page 10 - Wiring the System; Configuration Worksheets

Wiring the System 3M Model D-2400 6 Configuration Worksheets Use Configuration Worksheets 1 through 3 (located at the end of this document) to plan and record your systemconfiguration. You can record the system wire locations, wire color scheme, and program settings on theworksheets. Store the works...

Page 11 - The locations of the jumpers are shown in Figure 6.

3M Model D-2400 Programming the System 7 Programming the System Program the system to conform to your planned configuration and desired operation. Hardware (Jumpers) Select Call Station(s) to receive ALL CALL and music/messaging during STANDBY mode. (A closed jumperturns ALL CALL and music/messaging...

Page 12 - Programming the System; Programming the Selector; To enter the programming state, simultaneously:; Parameter; To input data at the cursor position, do one of the following:

Programming the System 3M Model D-2400 8 Programming the Selector Programming State 1 2 3 4 5 6 7 8 9 0 MENU TALK SP-389C Figure 5. D-2400 Keypad To program the D-2400, it is necessary to put the system in theprogramming state. From this state, the entire system is configuredand all memorized parame...

Page 13 - Key; pad

3M Model D-2400 Programming the System 9 Keypad FunctionDefinitions(Programming State) Key functions are defined below. Key Function HOLD (Shift) Shifts between upper and lower case for text data. UP ARROW Increments data by 1. Fields wrap around. DOWN ARROW Decrements data by 1. Fields wrap around....

Page 15 - Error Message; The system will display one error message: No Communication.; Parameter Selection; Stations are numbered starting with 1

3M Model D-2400 Programming the System 11 Error Message The system will display one error message: No Communication. The message occurs when there is no communications between the Selectorand Controller. To correct this: 1. Be sure Controller is powered on. 2. Be sure pins 2 and 3 of J22 on the Cont...

Page 16 - To re-initialize the Selector to its original factory settings:

Programming the System 3M Model D-2400 12 A value (Off, 1 to 16 inclusive). Priority station #, always moves to top ofqueue. On or Off. Enables the 30 second station connection time out. Default = On. Assignment of station names 01 through Max Stations where xx indicatesstation #. Default = PUMP # x...

Page 17 - To set the outbound ALL CALL Volume Level:; Outbound Talk Volume Level; To set the outbound talk volume, do the following:

3M Model D-2400 Adjusting the System 13 Adjusting the System Communications Controller You must remove the cover from the Communications Controller to perform the following adjustments. Outbound ALL CALL Volume Level To set the outbound ALL CALL Volume Level: 1. Ask another attendant to stand near a...

Page 18 - Adjusting the System; Repeat Steps 2 and 3 until the volume is satisfactory.; Inbound Audio Volume Level; To set the inbound audio volume level:; VOX (Voice Activated Transmission) Sensitivity Level

Adjusting the System 3M Model D-2400 14 Outbound Music/Messaging Level (Only for Systems That Use Music/Messaging) To set the outbound Music/Messaging level, do the following: 1. Ask another attendant to stand near a Call Station that is not in use and has Music/Messaging activated.(See the Communic...

Page 19 - Testing the Functions

3M Model D-2400 Adjusting the System 15 To set the VOX sensitivity level: 1. Follow the directions under the section Programming the Selector to put the Selector in Programming mode. 2. Locate the VOX Enable screen and be sure it is set to ON. 3. Locate the VOX Sensitive screen and press the right-a...

Page 21 - Adjusting inbound volume.

3M Model D-2400 Training Users 17 Training Users Train users of the Convenience Store Intercom System, Model D-2400, by performing the following steps: 1. Powering the system up (it should remain on). 2. Answering a call. 3. Initiating a call. 4. Adjusting inbound volume. 5. Operation of any applica...

Page 22 - Training Users

Training Users 3M Model D-2400 18 This page intentionally left blank.

Page 24 - CONFIGURATION WORKSHEET 2

Configuration Worksheets 3M Model D-2400 20 RECORD SETTINGS AND WIRE COLORS. STORE THIS DOCUMENT IN THE COMMUNICATIONS CONTROLLER. IMPORTANT RECORD WIRE COLORS WIRE COLORS RECORD RECORD WIRE COLORS WIRE COLORS RECORD WIRE COLORS RECORD TO POWER TO ADDITIONAL STATION SELECTORS Max Station PriorityAut...

Page 25 - COMMUNICATIONS CONTROLLER-STATION SELECTOR; AUDIO CONNECTIONS

3M Model D-2400 Configuration Worksheets 21 RECORDWIRE COLORS RECORDWIRE COLORS WIRE COLORS RECORD WIRE COLORS RECORD MUSIC/MESSAGE TO SOURCE STATION SELECTORS TO ADDITIONAL COMMUNICATIONS CONTROLLER-STATION SELECTOR CONFIGURATION WORKSHEET 3 COMMUNICATIONS CONTROLLER. STORE THIS DOCUMENT IN THE REC...

Page 26 - Food Services Trade Department; Printed on recycled paper.

3M Food Services Trade Department 3M CenterSt. Paul, MN 55144-1000 Printed on recycled paper. Printed in U.S.A. © 3M 2001 January 78-6912-0725-8 Rev C