3M 9000PD - Manuals

5 Introduction 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Introduction Thank You for Choosing 3M Thank you for choosing 3M equipment. This product has been produced in accordance with 3M’s highest quality and safety standards to ensure smooth and troublefree use in the years to come. Fo...

6 Introduction 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved.  WARNING To reduce the risk associated with hazardous voltage: • Do not attempt to service the Wall Display other than performing routine lamp replacement. Service should only be performed by a 3M authorized service provider. As...

7 Introduction 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved.  WARNING To reduce the risk of environmental contamination due to lead based solder: • Don’t throw circuit boards in the trash. Dispose of circuit boards in accordance with your respective governmental agencies for hazardous was...

8 Introduction 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. IMPORTANT NOTES • In some countries, the voltage is not stable. This appliance is designed to operate within a range of 100~240 Vac. In these countries, it is recommended to install a power stabilizer unit. • Do not manually open...

9 Introduction 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Product Safety Label The following safety label is used on or within the 3M Digital WallDisplay to alert you to this area requiring your attention. Wall Display fro m 3 M Save These Instructions The information contained in this ...

10 Introduction 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Netscape and the Netscape N and Ship’s Wheel logos are registered trademarks of Netscape Communications Corporation in the U.S. and other countries. Navigator and Communicator are also trademarks of Netscape Communications Corpo...

11 Introduction 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Model Identification and Differences Identify Model The nameplate, located behind the storage door, identifies the 3M Digital WallDisplay (DWD). Push the storage door to open it. The figure below shows the nameplate, and the tab...

12 Introduction 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Contents The 3M Digital WallDisplay is shipped with the necessary cables required for standard VCR, PC, Macintosh or laptop computer connections. Carefully unpack and verify that you have all of the items shown below. If any are...

13 Introduction 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. PC AUDIO USB MOUSE SERIAL MOUSE RS-232 AUDIO VIDEO COMPUTER ROW 1 2 (THIS ROW FOR DIGITAL WHITEBOARD OPTION ONLY) PRINTER COMPUTER S-VIDEO RCA VGA DVI-D OUT IN MENU KEYPAD 1 2 3 4 Wall Display fro m 3 M Part Identification 1 3 5...

14 Introduction 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. 3M Digital WallDisplay Features The 3M Digital WallDisplay combines the following features into one sleek, sophisticated package. • Full connectivity for computer or video presentations • Large 60˝ diagonal screen • 4:3 screen a...

15 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Installation and System Setup Installation and System Setup Recommendation and Things to Consider Before Installing Location of Unit • Place near AC outlet. The AC power connection is located on the lower-left corner of the 3M Digital WallDi...

16 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Installation and System Setup Installing the Wall Bracket Unpacking Wall Bracket and Hardware 1. Place the shipping container face up on the floor. 2. Open the end of the shipping container. 3. Slide the shipping tray partially out the conta...

17 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Installation and System Setup Hanging the 3M Digital WallDisplay Unpacking the 3M Digital WallDisplay 1. Place the shipping container face up on the floor and open the end previous opened. 2. Slide the shipping tray out of the shipping conta...

18 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Installation and System Setup Hanging on the Wall 1. If possible, position the 3M Digital WallDisplay and shipping tray in front of the wall where the bracket is located. Position the unit so that the projection arm is closest to the wall. 2...

19 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Installation and System Setup System Setup It only takes a few minutes to connect the 3M Digital WallDisplay to your computer, VCR, DVD player, video conference unit, or other devices.The connection panel is located underneath the bottom rig...

20 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Operation Operation Startup 1. Plug power cord into wall socket. 2. Flip on the Master Power Switch beneath the lower left corner of the 3M Digital WallDisplay, near the 3M label. This should stay on at all times. Now the 3M Digital WallDisp...

21 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Operation Shutdown 1. Press the On/Off Button on the bottom center panel of the 3M Digital WallDisplay unit. 2. The lamp will turn off and the projector arm will return to its housing. The On/Off Button will flash red as the arm closes. Note...

22 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Remote Control Unit Remote Control Unit Features The remote control sensor is on the front lower panel of the 3M Digital WallDisplay unit. The distance between the sensor and remote control must be shorter than 4 meters (13 feet). The remote...

23 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Remote Control Unit Forward Keypad Power Press to turn the 3M Digital WallDisplay on/off. When power is turned on, the 3M Digital WallDisplay will automatically extend the projection arm and ignite the lamp. Mute Press to temporarily turn of...

24 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Remote Control Unit Rear Keypad Pointer Press to turn the pointing function on/off. A green dot will appear on the screen. The dot can be controlled by pressing the arrows on the Disk Pad . Volume Press the + button to increase or the - butt...

25 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Remote Control Unit Installing or Replacing Batteries 1. Push and slide the battery compartment tab in the direction shown, then lift it off. 2. Install two AAA batteries as indicated by the diagram inside the compartment. 3. Snap the batter...

26 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Menu System Menu System Menu Navigation Most adjustments and settings are available in the main menu and sub-menus. To navigate and make adjustments, use the 3M Digital WallDisplay’s Menu Keypad button or the remote control’s Menu and Disk P...

28 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Menu System Mute Menu Function The Mute menu function turns the sound on and off. To turn the Mute menu function on: 1. Open the menu system by pressing the remote control Menu button or any arrow on the Menu Keypad . 2. Select the Mute menu...

32 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Maintenance Maintenance General Maintenance For general cleaning of the screen and exterior of the 3M Digital WallDisplay, use a damp cloth or dry cleaning cloth such as the 3M High Performance Cleaning Cloth.Standard dry-erase cleaners may ...

33 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Maintenance Lamp Replacement 1. Turn the power off and disconnect the power cord from the outlet. 2. Allow approximately 45 minutes for the lamp to cool, if necessary. 3. There are two indentations behind the top of the facade, near each end...

34 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Maintenance 5a. Hold down this receptacle with your left thumb and (5b) pull connectors out of the receptacle with other hand. 5b 5a 6. Open the latch by moving the metal lever to the left. Lever 7. While holding the latch open, grasp the la...

35 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Maintenance 11. Align the slots and tabs of the right side of the facade and projection arm as shown, then snap firmly into place. 12. Align the slots and tabs of the left side of the facade and projection head as shown, then snap firmly int...

36 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Maintenance Resetting Lamp Hours Please do the following within 10 minutes of turning power on after you replace the lamp. 1. Press the Menu Keypad or the Menu button on the remote control and use the Disk Pad to scroll down to the Tools men...

37 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Maintenance Replacing ProjectionScreen Replacing the 3M Digital WallDisplay screen is very simple. 1. Turn off the 3M Digital WallDisplay and disconnect the power cord from the wall outlet. 2. Remove the right and left side bezels. There are...

38 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Maintenance Optical Engine Adjustment The optical engine needs to be aligned when the vertical or horizontal images do not cover the screen or are tilted. Note: Before continuing with this adjustment, move the arm assembly up and down to rel...

39 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Maintenance 4. Loosen locking screw. Then use blade screwdriver on adjustment screw to move screen image from side to side if required. Tighten locking screw. 5. Locate adjustment screw for right side screen adjustment. Locate locking screw ...

40 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Maintenance 7. Locate adjustment screw for left side screen adjustment. Locate locking screw for left side adjustment. ��������� ������������� ������������������������� ���� 8. Loosen locking screw. Then use blade screwdriver on adjustment s...

41 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Troubleshooting Troubleshooting Common Problems and Solutions Symptom Cause Solution Power cannot be turned on. The power cord is disconnected. Insert the power cord into an AC socket. The Master Power Switch is not turned on. Turn on the Ma...

42 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Troubleshooting Common Problems and Solutions Symptom Cause Solution Desired input source cannot be detected. The input source is not active. A signal must be present for the input to be selected. Connect an active input source to unit. The ...

43 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Service Information Service Information Replacement Parts Description Part Number Power Cord (EU) 78-8131-0004-3 Power Cord (US) 78-8131-0005-0 Power Cord (UK) 78-8131-0003-5 Serial Mouse Cable 26-1015-0423-6 USB Cable 26-1015-0424-4 VGA Cab...

44 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Appendix Appendix 3M™ Digital WallDisplay Specifications Display Size 60" Diagonal viewing area Display Aspect Ratio 4:3 Display System Single Chip, DLP™ Texas Instruments technology DLP Chip Chip Diagonal Size 0.7 inch Number of Pixels ...

45 3M™ Digital WallDisplay © 3M 2005. All Rights Reserved. Appendix Input/Output Signal Specifications Computer Video Signal Analog 0.7Vp-p, 75 Ohms termination (positive polarity) Horizontal Sync Signal TTL Level (positive/negative polarity) Vertical Sync Signal TTL Level (positive/negative polarit...