3M 40800 - Manuals

TABLE OF CONTENTS (continued) i 5. Shipment, Handling, and Storage 5.1 Packed Machine Shipment and Handling ........................................................................... 15 5.2 Overseas Shipment Packaging (Optional) .........................................................................

9 12. Operation 12.1 Operator’s Correct Working Position ............................................................................... 25 12.2 Starting the Machine ........................................................................................................ 25 12.3 Starting Production ....

10 ABBREVIATIONS AND ACRONYMS LIST OF ABBREVIATIONS, ACRONYMS 3M-Matic - Trademark of 3M St. Paul, MN 55144- 1000 AccuGlide - Trademark of 3M St. Paul, MN 55144-1000 Scotch - Trademark of 3M St. Paul, MN 55144-1000 Drw. - drawing Ex. - for example Fig. - exploded view fi gure no. (spare parts) Figur...

1-INTRODUCTION 3M-Matic TM 700a Adjustable Case Sealer, Type 40800 Note – Shown above is the lower tape supply roll and bracket assembly in the alternate location. 1 1.1 Manufacturing Specif i cations / Description / Intended Use The 3M-Matic TM 700a Adjustable Case Sealer with AccuGlide TM 3 Taping...

3 2.1 Data Identifying Manufacturer and Machine 2011 June 700a-NA For Commercial Use Only 2-GENERAL INFORMATION

5 3-SAFETY 2011 June 700a-NA 3.1 General Safety Information Read all the instructions carefully before starting work with the machine; please pay particular atten-tion to sections marked by the symbol: The machine is provided with a LATCHING EMER-GENCY STOP BUTTON (Figure 3-1) ; when this button is ...

6 3.3 Table of Warnings • To reduce the risk associated with mechanical and electrical hazards: − Read, understand, and follow all safety and operating instructions before operating or servicing the case sealer. − Allow only properly trained and quali fi ed personnel to operate and service this equi...

7 3-SAFETY (continued) 2011 June 700a-NA Figure 3-7 WARNING Sharp Blade Figure 3-8 Figure 3-5 Figure 3-6 • To reduce the risk associated with sharp blade hazards: − Keep hands and fi ngers away from tape cutoff blades under orange blade guards. The blades are extremely sharp. WARNING Important! Tape...

18 7-INSTALLATION (continued) 2011 June 700a-NA 7.5 Removal of Plastic Ties Cut the plastic which attaches the top head to the frame and remove the polystyrene blocks (Figure 7-4). Cut the plastic strap which attaches the strip and the EMERGENCY STOP cable to the frame (Figure 7-5). Cut the plastic ...

19 7-INSTALLATION (continued) 2011 June 700a-NA 7.7 Completion of Taping Heads See Manual 2 for Complete Instructions:1. Place the Upper Taping Head in a convenient working position 2. Use Figure 7-8 and tape threading label. Position the tape supply roll so the adhesive side of tape is facing the f...

20 8.1 Description of the Working Cycle After having closed the top fl aps of the carton, the operator pushes it under the top infeed end in order to avoid the opening of the top fl aps. Further push- ing causes the two top and bottom belts to drive the box through the taping heads which automatical...

11 - SET UP AND ADJUSTMENTS (continued) 24 2011 June 700a-NA 11.5 Special Set-Up Procedure for Outer Column Re-Positioning Moving the outer columns up one set of mounting holes increases the maximum box height handled by the 700a case sealer and decreases the minimum conveyor bed height. 1 - Place s...

43 2011 June 700a-NA 700a Figure 2796 Ref. No. 3M Part No. Description 2796-1 78-8070-1536-3 Support – Guide Arm 2796-2 78-8010-7169-3 Screw – Hex Hd, M6 x 12 2796-3 26-1000-0010-3 Washer – Flat, M6 2796-4 78-8070-1537-1 Lever With Pivot 2796-5 78-8070-1538-9 Bushing 2796-6 26-1003-8816-9 Screw – Se...

48 2011 June 700a-NA 700a =1 7 4 3 5 2 16 16 6 6 6 6 18 17 13 14 15 12 12 11 21 19 10 29 31 31 5 8 9 30 32 23 23 2524 27 26 2122 28 2830 20 28 OPTIONAL 37 36 38 39 35 35 Figure 3433 Caster Option

52 2011 June 700a-NA 700a Figure 15234 / 1 (R/H) (L/H)

Accuglide 3Upper and LowerHigh SpeedTaping Heads2 Inch Type 10800 AccuGlide ™ is a Trademark of 3M, St. Paul, MN 55144-1000Printed in U.S.A. © 3M 2012 44-0009-2070-0 (E010712-NA) Instructions and Parts List Serial No. _____________________________________ For reference, record taping head(s) serial ...

i 4000563 IN TERTEK 3M-Matic ™ , AccuGlide ™ and Scotch ™ are Trademarks of 3M St. Paul, MN 55144-1000Printed in U.S.A. 3M Industrial Adhesives and Tapes 3M Center, Building 220-5E-06St. Paul, MN 55144-1000 To Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch ® equipment you ordered. It has bee...

Replacement Parts And Service Information To Our Customers: This is the 3M-Matic™/AccuGlide™/Scotch ® equipment you ordered. It has been set up and tested in the factory with Scotch ® tapes. If any problems occur when operating this equipment and you desire a service call or phone consultation, call...

8 AccuGlide ™ , Scotch ™ , and 3M-Matic ™ are Trademarks of 3M, St. Paul, Minnesota 55144-1000 Equipment Warranty and Limited Remedy: Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO , ANY IMPLIED...

1 AccuGlide 3 - 2" - NA 2012 January Intended Use The intended use of the AccuGlide™ 3 Upper and Lower Taping Heads - 2 Inch is to apply a "C" clip of Scotch ® pressure-sensitive fi lm box sealing tape to the top and/or bottom center seam of regular slotted containers. These taping heads...

6 AccuGlide 3 - 2" - NA 2012 January Specif i cations 1. Tape: For use with Scotch ® pressure-sensitive fi lm box sealing tapes. 2. Tape Width: 36mm or 1-1/2 inches minimum to 48mm [2 inches] maximum. 3. Tape Roll Diameter: Up to 405mm [16 inches] maximum on a 76.2mm [3 inch] diameter core. (Acc...

8 Installation 1. The box conveying system must positively propel the box in a continuous motion, not exceeding 0.40 m/s [80 feet per minute], past the taping head assembly since the box motion actuates the taping mechanism. 2. If a pusher or cleated conveyor is being used, steps should be taken in ...

11 Operation (continued) Manually turn tape roll to create slack tape while pulling threading needle through tape applying mechanism until needle is through and tape is in alignment with applying roller. Excess tape can be cut with a scissors at applying roller. Figure 3-4 Place tape roll on tape dr...

18 Problem Tape is tabbing on the trailing leg on the back of the box The tape end does not stay in application position in front of the applying roller Tape not centered on box seam Cause There is excess tension on the tape drum assembly and/or the one-way tension roller assembly Rollers in the tap...

AccuGlide 3 - 2" - NA 2012 January AccuGlide ™ 3 - 2" 24 25 1 3 2 4 8 11 10 12 16 15 17 17 18 19 13 13 13 9 7 5 23 13 23 27 20 29 27 26 28 29 21 22 Figure 10925 – Upper Head