BMW K 1200 LT - 2005- User Manual

4 Over vi ew a n d o pera ti o n 1 1 Left button (ribbed) 2 Right button 3 LED 4 Radio remote control unit 5 Status LED (on the vehicle) L Note: Do not be tempted to use the remote control unit to lock the keys inside a stowage compart-ment. If you were to mislay the remote control unit the keys wou...

5 Over vi ew a n d o pera ti o n 1 Functions of the remote control unit Operation Button 1 Confirmation Press once Lock central locking – Press again Activate alarm func-tion and immobiliser Turn indicators flash 2x Alarm tone sounds 2x (if pro-grammed) Press for third time Deactivate motion sensor ...

6 Over vi ew a n d o pera ti o n 1 Code card The anti-theft alarm is supplied complete with a sealed enve-lope containing a code card 1 . The number stated on the code card (remove the adhesive label) is the code for deactivat-ing the anti-theft alarm by means of the ignition ( b 17). It is advisabl...

7 Immo bili s e r 2 Once the immobiliser has been activated the engine will refuse to start even if an authorised key is used for the start attempt. You can tell whether the immobiliser is activated by switching on the ignition and observing LED 5 ; if the immobi- liser is active it will light up wh...

9 Immo bili s e r 2 Deactivation Deactivating the immobi-liser with the remote con-trol unit The immobiliser is deactivated • by pressing button 2 on the remote control unit once (if the immobiliser was activated automatically beforehand when you switched off the ignition, it is reactivated 30 secon...

12 Ala rm f unct io n 3 Activation phases 15 seconds elapse before the alarm function is fully active. Status of the anti-theft alarm LED Activation phase (15 seconds) Rapid flashing (0.1 sec. on/ 0.5 sec. off)If the motion sensor was switched off: Rapid flashing (0.1 sec. on/ 0.2 sec. off) Anti-the...

3 13 Ala rm f unct io n How the alarm is triggered How the alarm is triggered The alarm can by triggered• by the motion sensor• by an attempt to switch on the ignition without deactivating the anti-theft alarm before-hand • by disconnection of the anti- theft alarm from the motorcy-cle's battery (th...

16 Ala rm f unct io n 3 Reasons for an alarm Reasons for an alarm Once you have deactivated the alarm function, the LED shows you reasons for alarms, if any, that were triggered in your absence:• Flashes 1x: Motion sensor • Flashes 2x: Ignition on while the anti-theft alarm was primed • Flashes 3x: ...

4 19 Cen tr a l l o c k in g sy stem Manual opening and closing You can still open and close the cases, the topcase and the radio compartment manually with the key, as described in the Rider’s Manual. Manual operation DWA_5_2_eng.book Seite 19 Dienstag, 1. März 2005 4:59 16

20 Cen tr a l l o c k in g sy stem 4 Remote control unit Closing with the remote control unit Press button 1 on the remote control unit once to lock the cases, the topcase and the radio compartment. The lids are locked irrespective of whether or not a particular lock was engaged manually beforehand....

4 21 Cen tr a l l o c k in g sy stem Emergency unlocking If the compartments were locked by the central locking system and, for some reason, the remote control unit is not to hand, you can use the emer-gency unlocking routine to open them. Emergency unlock-ing is independent of the cur-rent status o...

22 Cen tr a l l o c k in g sy stem 4 Safety shutdown Overly frequent locking and unlocking within a short period of time could cause the motors of the central locking system to become very warm. An override function can cut in and interrupt operation in order to avoid damage to the motors: these int...

5 23 Li ght s The lights are switched on• when you deactivate the alarm function or• by switching off the ignition, if programmed ( b 26) The lights dim out after 20 seconds. Map-reading light The map-reading light switches on automatically if switch 1 is in position c . Lights 1 a b c DWA_5_2_eng.b...

24 P rog ra mming 6 You can customise the BMW anti-theft alarm system to suit your needs and preferences as follows:• Acoustic confirmation after activation/deactivation of the anti-theft alarm in addition to turn indicators flashing • Automatic activation of lights when ignition is switched off • R...

6 25 P rog ra mming Default settings Setting Status Acoustic acknowledgement after activation/deactivation OFF Automatic activation of lights when ignition is switched off ON Type of acoustic alarm Intermittent Automatic activation of alarm function when ignition is switched off OFF Automatic activa...

26 P rog ra mming 6 Programming mode, accessing Step Action Confirmation 1 Deactivate the anti-theft alarm 2 Steps 3 to 7 must be com-pleted within 10 seconds 3 Switch on the ignition Wait until LED 5 goes out 4 Press button 2 once LED lights up briefly 5 Switch off the ignition LED shows the number...

6 27 P rog ra mming Programming The number of times LED 5 flashes indicates the step to which you have progressed in programming.An alarm tone sounds as confir-mation when you press button 1 , whereas an acknowl- edgement tone sounds when you press button 2 . The LED stops flashing and four acknowle...

28 P rog ra mming 6 Exiting programming mode L Note: Note that you cannot activate the function for priming the alarm automatically when the ignition is switched off unless the system is also set up for au-tomatic activation of the immo-biliser. Programming mode is cancelled • by switching off the i...

7 29 R e mo te c o n tro l u n its If you want to start using an extra remote control unit or replace a remote control unit that has been mislaid, you always have to register all the remote control units with the anti-theft alarm. You can regis-ter a maximum of four remote control units. L Note: The...

32 R e mo te c o n tro l u n its 7 Exiting registration mode Registration terminates• once four remote control units have been registered • if the ignition is switched off• if, after a remote control unit has been registered, 30 sec-onds elapse without a button being pressed The LED flashes and the ...

7 33 R e mo te c o n tro l u n its Synchronising the remote control unit Synchronisation is necessary if the buttons on the remote con-trol unit are pressed more than 256 times outside the range of the receiver. When this limit is reached the receiver on the motorcycle no longer reacts to signals fr...

34 Ca re a n d ma int e nanc e 8 Changing the batteries in the remote control units The batteries in the remote con-trol units are due for replace-ment after approximately 2 to 3 years.You can tell when a bat-tery is weak if LED 3 lights up only briefly, or not at all, when a button is pressed. e At...

36 Techn ica l d a ta 9 Anti-theft alarm Neutral activation time 15 seconds Alarm duration 26 seconds Neutral time between two consecutive alarms 10 seconds Operating temperature –40 °C to +85 °C Trigger angle of the motion sensor ±0.7° Current consumption (idle current with system active) < 3 mA...

37 In d e x i A Activation phases, 12Activation with motion sensor, 10Alarm, 13Alarm function Deactivating with remote control unit, 14Deactivating without remote control unit, 15 C Changing the battery, 34, 35Code card, 6Code number, 6Controls, 4 D Default settings, 25 E Emergency unlocking, 21 F F...