Black & Decker VEC010BD- Manual
Black & Decker VEC010BD– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – SAVE THESE INSTRUCTIONS; IMPORTANT SAFETY INSTRUCTIONS
- Page 3 – TABLE OF CONTENTS; INTRODUCTION; Thank you for choosing the; FEATURES; exclusive recessed cable holsters
- Page 4 – USING THE UNIT AS A JUMP-STARTER; Connect the red clamp first, then; Procedure for jump-starting POSITIVE GROUND SYSTEMS; • If the audible Reverse Connection Polarity Alarm sounds after; • Illuminate areas under the hood, inside tents and work areas.
- Page 5 – CARE AND MAINTENANCE; The battery can be recharged using an AC or DC adapter (see below).; AC Recharge; RECHARGE; WARNINGS; • Jump-Starter Power Switch should be OFF prior to jump-starting.; USING THE UNIT AS A 12 VOLT DC PORTABLE POWER SUPPLY; Estimated 12 Volt DC Operation Time; Cell phone; CAUTION
- Page 6 – 2 Volt DC Charging
VEC010BD
KEY FEATURES:
• Rechargeable Jump-Start
System
• Easy-to-Read Charge
Indicators
•
Emergency Area Light
• Keyless ON/OFF Power
Switch
• 12 Volt DC Accessory
Outlet
• Battery Status Check
USER’S MANUAL
& WARRANTY INFORMATION
IMPORTANT SAFETY INFORMATION, SAVE THESE INSTRUCTIONS
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND
THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS
PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.
www.vectormfg.com
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312 U.S.
Toll Free: (800) 618-5178
8
START-IT
Jump-Starter
12 Volt DC Power Supply
Cordless • Rechargeable
TWO YEAR LIMITED WARRANTY PROGRAM
This limited warranty program is the only one that applies to this product, and it sets forth all the
responsibilities of Vector Manufacturing, regarding this product. There is no other warranty, other than those
described herein.
This Vector Manufacturing product is warranted, to the original purchaser only, to be free of defects in
materials and workmanship for two years from the date of purchase without additional charge. The
warranty does not extend to subsequent purchasers or users. Vector Manufacturing will not be responsible
for any amount of damage in excess of the retail purchase price of the product under any circumstances.
Incidental and consequential damages are specifically excluded from coverage under this warranty.
This product is not intended for commercial use. This warranty does not apply to accessories or damage to
units from misuse or incorrect installation. Misuse includes wiring or connecting to improper polarity power
sources.
RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned postage prepaid to
manufacturer. Any defective product, other than accessories, that is returned to manufacturer within 30 days
of the date of purchase will be replaced free of charge. If such a product is returned more than 30 days
but less than two years from the purchase date, manufacturer will repair the unit or, at its option, replace it
free of charge. If the unit is repaired, new or reconditioned replacement parts may be used, at Vector
Manufacturing’s option. A unit may be replaced with a new or reconditioned unit of the same or
comparable design. The repaired or replaced unit will then be warranted under the terms of the remainder
of the warranty period. The customer is responsible for the shipping charges on all returned items after 30
days. During the warranty period, manufacturer will be responsible for the return shipping charges.
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting from
normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to usage or
exposure to sunlight), accidents, damage during shipping to our service facility, alterations, unauthorized
use or repair, neglect, misuse, abuse, failure to follow instructions for care and maintenance, fire, flood and
Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department toll free at
(800) 618-5178 for general repair information and charges if applicable. You may also contact us through
our website at www.vectormfg.com.
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations on
how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages,
so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser specific legal
rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Vector Manufacturing Technical Support
by telephone, fax or mail (see below). We suggest that you keep the original packaging in case you need
to ship the unit. When returning a product, include your name, address, phone number, dated sales receipt
(or copy) and a description of the reason for return and product serial number. After repairing or replacing
the unit, we will make every effort to return it to you within four weeks.
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector Manufacturing.
Enter “VEC010BD” as Model and “Jump-Starter” as Product Type. All Vector Manufacturing products must
be registered within 10 days of purchase to activate this warranty. Mail the completed registration form,
along with a copy of the original sales receipt to:
ATTN.: CUSTOMER SERVICE
4140 SW 30th Ave., Ft. Lauderdale, FL 33312
• TOLL FREE: (800) 618-5178 • FAX: (954) 584-5556 •
BD42905
© 2005 VECTOR MANUFACTURING
MADE IN CHINA
Vec010BD_Manual_042905 5/9/05 1:00 PM Page 8
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Black & Decker VEC010BD
Summary
iii CAUTIONSUse only the supplied cords/adapters for recharging this unit. Do not recharge for more than 3-4 hours maximum using 12 volt DC method. Recharge unit after each use.All on/off switches should be in the OFF position when the unit is charging or not in use. Make sure all switches are in th...
iv 1 TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Battery Charge Status . . . . . . . . . . ...
3 USING THE UNIT AS A JUMP-STARTER This Jump-Starter is equipped with a safety Power Switch that only allows energy toflow when proper connections are made to battery and frame. Once theconnections are properly made, turn the switch ON to jump-start the vehicle. 1. Turn OFF vehicle ignition and all ...
