Black & Decker BDCMTTS-XE- Manual

Page 2 - PARTS AND FEATURES; Trim saw attachment; Figure A

2 PARTS AND FEATURES 1. Trim saw attachment 2. Lock-off button 3. Spindle lock 4. Wrench 5. Shoe 6. Upper guard 7. Lower saw blade guard 8. Retracting lever Figure A 1 2 4 3 5 6 7 8

Page 3 - ENGLISH; Read all safety warnings and all instructions.; Failure to follow the; Save all warnings and instructions for future reference.; Read all safety warnings and all instructions provided with your; Failure to; SPECIFIC SAFETy RUlES; Intended use; before using this accessory.; General power tool safety warnings; WARNING! Read all safety warnings and all; Failure to follow the warnings and; This tool is intended for consumer use only.

3 ENGLISH (Original instructions) WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. WARNING: Read all safety warnings and all instr...

Page 4 - CAUSES AND OPERATOR PREVENTION OF KICKBACK; motion or kickback may occur.; lOWER GUARD SAFETy INSTRUCTIONS; properly, they must be serviced before use.; ADDITIONAl SAFETy INSTRUCTIONS

4 ENGLISH (Original instructions) CAUSES AND OPERATOR PREVENTION OF KICKBACK • Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator. • When the blade is pinched or bound tightly by the kerf clos...

Page 5 - Causes and Operator Prevention of; AlWAyS use proper eye protection.

5 ENGLISH (Original instructions) • Keep your body positioned to either side of the blade, but not in line with the saw blade. KICKBACK could cause the saw to jump backwards (see Causes and Operator Prevention of Kickback and KICKBACK) . • Avoid cutting nails. Inspect for and remove all nails from l...

Page 6 - system wherever possible.; SyMBOlS; TO REDUCE THE RISK OF KICKBACK; Figure C; Figure D

6 ENGLISH (Original instructions) WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body. Always ...

Page 7 - ATTACHING AND REMOVING THE BlADE:; lOWER BlADE GUARD

Secure the workpiece to a stable platform as shown in Figure D . It is important to support the work properly to minimize body exposure, blade binding, or loss of control. ASSEMBly/ADjUSTMENT SET-UP WARNING: To reduce the risk of injury, always remove battery from saw before any of the following adj...

Page 8 - SAVE THESE INSTRUCTIONS; SUPPORTING lARGE PANElS / SECURING WORKPIECE; Figure B

• Always secure work to prevent workpiece movement during cut. • Do not try to force saw back on line if your cut begins to go off line. This can cause KICKBACK. Stop saw and allow blade to coast down to a stop. Withdraw from cut and start a new cut on the line. • Do not back up a rotating blade in ...

Page 9 - OPERATING INSTRUCTIONS; important safety warnings and instructions prior to using tool.; To reduce the risk of injury; Risk of lacerations or burns.; OPERATION

WARNING: To minimize the risk of eye injury, always use eye protection. Carbide is a hard but brittle material. Foreign objects in the work piece such as wire or nails can cause tips to crack or break. Only operate saw when proper saw blade guard is in place. Mount blade securely in proper rotation ...

Page 10 - adjustment and set up instructions.; SAWING; Figure G; • For best results use a blade with 20-24 cutting teeth.; WARNING; Figure G

BlADE SElECTION your circular saw is designed for use with 3-3/8 inch (86 mm) diameter blades that have a 15 mm diameter bore. Blades must be rated for 3000 RPM operation (or higher). NOTE: This saw is designed to cut wood and plastic. Do not use masonry or metal cutting blades. DO NOT use any abras...

Page 11 - Technical data; TrimSaw; MAINTENANCE; never immerse any part of the tool into a liquid.; ACCESSORIES; TROuBLEShOOTING; Problem; • Unit will not start.

Technical data TrimSaw Weight 729g MAINTENANCE Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those l...

Page 12 - Australia & New Zealand

07/2012 Australia & New Zealand Stanley Black & Decker 82 Taryn Drive, Epping, VIC 3076 Australia Tel.1800 444 224 (Aust) or Tel. 0800 339 258 (NZ) 90589521 REV-0