Black & Decker 2233 - Manual
Black & Decker 2233 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – AIR SPRING; Male spade connector; Air Line & Wiring Diagram; Ring Terminal; Compressor Attachment; Figure “A”
- Page 3 – SIDE VIEW OF CONTROL PANEL; SUP; TO AIR SPRINGS; FROM COMPRESSOR
- Page 4 – There are two wires (one red and one black) attached to the; FUSE HOLDER; FIRESTONE INDUSTRIAL PRODUCTS
I
NSTALLATION
INSTRUCTIONS
Congratulations on your purchase of a new Level Command
kit. This kit was designed to provide inflation control of your
air helper springs. This kit will be an asset to your vehicle,
meeting nearly all of your air supply needs.
Please take a few minutes to read through the instructions,
identify the components, and learn how to properly install your
Level Command kit.
N
OTE
:
The Level Command kit can be used with all air helper
spring products. If you are installing an air suspension system,
do not install the air line tubing to the air springs as stated in
the suspension system instruction manual. If you are adding
the Level Command kit to an existing air suspension system,
you will need to deflate the air springs and remove the air line
tubing.
N
OTE
ON
C
ONNECTING
THE
AIR
LINE
TUBING
:
Cut the air line tubing as squarely as possible. To connect
the air line tubing to the fittings, push the tubing into the fittings
as far as possible. If for any reason the tubing must be removed,
first release the air pressure from the air helper spring. Push the
collar toward the body of the fitting and the pull out the tubing.
To reassemble, make sure the tubing is cut squarely and push
the tubing back into the fitting.
T
OOLS
REQUIRED
:
• 3/16"
DRILL
BIT
• 3/8"
DRILL
BIT
• 1/4"
DRILL
BIT
• P
OWER
DRILL
• W
IRE
CRIMPER
/
STRIPPER
• P
LIERS
• P
HILLIPS
SCREW
DRIVER
• U
TILITY
KNIFE
• (2) 7/16"
WRENCHES
• C
ENTER
PUNCH
0
150
30
120
60
90
200
400
600
800
1000
psi
kPa
PSI
SINGLE AIR CONTROL PANEL
1
COMPRESSOR
9210
1
30 FT. AIR LINE TUBING
1
1/8" NPT PUSH-TO-CONNECT
STRAIGHT FITTING
3055
1
PUSH-TO-CONNECT
T-FITTING
3025
2
10 -32 x 1" MACHINE SCREW
5
10 -32 LOCK NUT
5
24-8204
03-01
NAD-30665-2
2097 / 2187 / 2227 / 2233
P
ARTS
LIST
L
EVEL
C
OMMAND
#10 FLAT WASHER
7
15 FT. 16 GAGE WIRE
1
IN-LINE FUSE HOLDER
1
20 AMP BLADE FUSE
1
FEMALE SPADE CONNECTOR
2
MALE SPADE CONNECTOR
1
RING TERMINAL
1
WIRE CONNECTOR
2
NYLON TIE
15
L
EVEL
C
OMMAND
WITH
9210 C
OMPRESSOR
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
AIR SPRING (sold separately) 0 150 30 120 60 90 200 400 600 800 1000 psi kPa PSI AIR SPRING (sold separately) “T” FITTING Male spade connector Femal spade connector Inline fuse connector Wire connector Air Line & Wiring Diagram FUSE GROUND AIR LINE AIR LINE Connectors: Ring Terminal RED WHITE WH...
LOCK NUTS WASHERS MACHINE SREWS CONTROL PANEL BRACKET WASHERS S TEP 1 - S ELECT A MOUNTING LOCATION FOR THE CONTROL PANEL Select a mounting surface under the dashboard or other protected location. Using the control panel as a template, mark each of the mounting points with acenter punch. Drill a 3/1...
BACK OF GAUGE RING CONNECTOR (TO GROUND) POSITIVE WIRE (TO DASHBOARD ILLUMINATION WIRE) S TEP 6 - A TTACH THE CONTROL PANEL TO THE DASHBOARD Place the air control panel on the dash where the holes were drilled in Step 1. Using the provided machine screws, lock nuts, and washers attach the air contro...
