Black Box MDR210A-485 - Manual

Page 3 - Description

3 Description The MDR210A-485 uses an embedded 100-milliwatt, frequency-hopping wireless modem that provides communication between a local RS485 network and a remote network of RS485 connected devices. The MDR210A-485 will automatically sense the direction of data flow and switch the RS485 and Radio...

Page 4 - Features; General Purpose; MDR210A-485; Provides remote capability to RS485 Modbus networks.

4 Features res General Purpose 900 MHz. Spread Spectrum Frequency Hopping Transceiv General MDR210A-485 Frequency Range 902 to 928 MHz., unlicensed ISM Band Type Frequency Hopping Spread Spectrum Transceiver Frequency Control Direct FM Transport Protocol Transparent networking Channel Capacity Hops ...

Page 5 - Radio; Approved Antennas; Mfr Model

5 9XSTREAM-192/96 Radio Introduction The 9XSTREAM-192/96 radio is a 100-milliwatt frequency hopping wireless modem that communicates with other equipment using a standard 19200 or 9600-baud asynchronous serial data stream. The radio is half-duplex and can sustain a continuous data stream at the spec...

Page 6 - XStream Frequency Hopping Data Radio

6 9XStream Frequency Hopping Data Radio FCC Compliance Warning: Changes or modifications to the 9XStream Data Radio not expressly approved by MaxStream, Inc. could void the user’s authority to operate this product. Note: This equipment has been tested and found to comply with the limits for a Class ...

Page 7 - Application Fields

7 Antenna Antenna Connector MMCX Female Antenna Impedance 50 Ohms unbalanced Approved Antennas Integral wire antenna (factory installed) Astron AXQ9PRLMMCX – 1/4 wave flexible whip Astron AXH900 RP SMAR – 1/2 wave flexible whip, SMA Serial Port Scanning The Scan Function is provided to assist the us...

Page 8 - Module Addresses; provide another level of addressing among the MDR210A-485; Data Validity

8 hop in a different sequence) the two modules will jump to separate channels on the next hop. Using networks, multiple module pairs can operate in the same vicinity with minimal interference from each other. The network parameter is user-definable using the MDR210A-485 Set-up Hop Table. Module Addr...

Page 9 - Glossary; Data Buffer

9 Figure 2a – Generation of Data Packets Data Validity (Cont.) To verify data integrity, a 16-bit cyclic redundancy check (CRC) is computed for the transmitted data and attached to the end of each data packet before transmission. The receiver will then compute the CRC on all incoming data. Any recei...

Page 11 - Why does Sensitivity Matter?

11 Application Notes Why does Sensitivity Matter? Receiver sensitivity is the lowest power level at which the receiver can detect a wave and demodulate data. Sensitivity is purely a receiver specification and is independent of the transmitter. As the wave propagates away from the transmitter, it att...

Page 12 - Application Notes

12 Application Notes (cont.) Range Received Detectable by Detectable by (meters) Power MDR210A-485 Commercial Radio 100 -68.526 dBm YES YES 500 -82.506 dBm YES YES 1000 -88.526 dBm YES YES 3000 -92.048 dBm YES NO 5000 -102.506 dBm YES NO 8000 -106.588 dBm YES NO 10000 -108.526 dBm YES NO 11265 (7mil...

Page 13 - Appendix A – Specifications

13 Appendix A – Specifications General Frequency Range 902 to 928 MHz, unlicensed ISM Band Type Frequency Hopping Spread Spectrum Transceiver Frequency Control Direct FM Transport Protocol Transparent Networking Channel Capacity Hops through 25 channels. Up to 65,000 NetIDs. Serial Data Interface As...

Page 14 - FCC Compliance Warning:

14 FCC Compliance Warning: Warning: This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired opera...

Black Box MDR210A-485 - Manual

Table of Contents:

Summary

Other Black Box Models