Page 3 - REFACE; Safety Information; Never install telephone wiring during a lightning storm.
P REFACE Preface Safety Information CAUTION! A LWAYS USE CAUTION WHEN INSTALLING TELEPHONE LINES . R EAD THE CAUTIONS BELOW FOR DETAILS ON SAFETY GUIDELINES TO PREVENT INJURY . l Never touch uninsulated telephone wires and terminals unless the telephone line has been disconnected at the Network Inte...
Page 4 - Electrostatic Discharge (ESD) Precautions; IC
4 Compact T1 - Release 6.1 Preface Electrostatic Discharge (ESD) Precautions Electrostatic Discharge (ESD) Precautions ESD can damage processors, circuit cards, and other electronic components. Always observe the following precautions before installing a system component. 1. Do not remove a componen...
Page 5 - In this Guide
Q UICK S TART Quick Start In this Guide n Unpacking and Inspection n Installation Environment n Assembly of Compact T1 n Wall Mounting n Rack Mounting (Optional Feature) n Compliant Installation n Chassis Connectors and Buttons n Interface Connectors n Local and Remote Management Option n Configurat...
Page 6 - Unpacking and Inspection
2 Compact T1 - Release 6.1 Quick Start Unpacking and Inspection Unpacking and Inspection WARNING! O BSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DEVICES . 1. Inspect containers for damage during shipment. Report any damage to the freight carrier for possible insurance claims. 2. Compare packing lis...
Page 7 - Assembly of Compact T1
Compact T1 - Release 6.1 3 Quick Start Assembly of Compact T1 Assembly of Compact T1 The cards should be positioned in the chassis as follows:Note: Slots are labeled on the top and the bottom of the chassis. l Power Supply in the POWER Slot l T1 Controller in Slot A l Service Cards can be in any slo...
Page 8 - Wall Mounting
4 Compact T1 - Release 6.1 Quick Start Wall Mounting Wall Mounting Before beginning the mounting process, verify that the area meets the following requirements: l A stable environment, clean and free from extremes of temperature, shock, vibration and EMI, that meets the all installation environment ...
Page 9 - To rack mount the Unit, follow the instructions below:
Compact T1 - Release 6.1 5 Quick Start Rack Mounting (Optional Feature) Rack Mounting (Optional Feature) Rack mounting kits are available for both 19 and 23 inch racks. To rack mount the Unit, follow the instructions below: 1. Attach bracket ears to rack mounting bracket using four #8-32 x 3/16"...
Page 13 - Compliant Installation; Signal Cables
Compact T1 - Release 6.1 9 Quick Start Compliant Installation Compliant Installation 1. Connect all of the signal cables as shown in the illustration above, and secure them with a plastic tie. Dress the signal cables toward the left of the unit. 2. If using the 115V Power Supply, connect the -48 VDC...
Page 14 - Ferrite Beads; Ferrite Beads shipped with Adit chassis:
10 Compact T1 - Release 6.1 Quick Start Compliant Installation Ferrite Beads To be compliant with Part 15A of the FCC and for NEBS compliant facilities, the following beads are included with each chassis, as well as additional ferrite bead(s) with the Service cards listed below. Ferrite Beads shippe...
Page 15 - Chassis Connectors and Buttons
Compact T1 - Release 6.1 11 Quick Start Chassis Connectors and Buttons Chassis Connectors and Buttons The following illustrations show all connectors on the back of the unit. Interface Connectors The following are the Compact T1 chassis interface connectors: l T1-1 and T1-2 line connection ports eac...
Page 16 - Chassis Ground Connector; Ground Terminals
12 Compact T1 - Release 6.1 Quick Start Interface Connectors Chassis Ground Connector 1. Route wire (#6 or #8 AWG copper) from building ground to lug on Unit. 2. Strip insulation off wire end, if necessary. 3. Loosen compression screw until opening is large enough to accept ground wire. 4. Insert gr...
Page 17 - Power Reset; AC Power; To connect the Power Cord:; Description; AC Power Connector
Compact T1 - Release 6.1 13 Quick Start Interface Connectors Power Reset This is a resetable circuit breaker. If at any time there is a short or power surge on the incoming AC/DC line, the breaker will trip to protect the Power supply from damage. Power Connections AC Power The AC Power cord is a st...
Page 19 - External Alarm Connector
Compact T1 - Release 6.1 15 Quick Start Interface Connectors External Alarm Connector The external alarm 6-pin connector with one input pair (pins 5 and 6) and two output pairs (pins 1 and 2 - major alarms; pins 3 and 4 - minor alarms). The pinouts are as follows: Pin # Description Explanation 1 Maj...
Page 20 - 5-Pair Telco Connectors; Pair
16 Compact T1 - Release 6.1 Quick Start Interface Connectors 25-Pair Telco Connectors Tip and Ring Analog Interfaces equipped with standard 25-pair Telco Connectors (female) for connection to key systems, fax machines, modems, and PBXs. These interfaces are also used for ISDN BRI ports and are jumpe...
Page 22 - Pin Number
18 Compact T1 - Release 6.1 Quick Start Interface Connectors RS-232 Craft Port (Female DB-9) The RS-232 craft port connector (female) is for connection to an external PC or Hayes-compatible modem for local or remote configuration, management, and performance monitoring using the Command Line Interfa...
Page 23 - T1 Connection Ports
Compact T1 - Release 6.1 19 Quick Start Interface Connectors T1 Connection Ports The T1 connection ports are each equipped with a standard RJ-48C (female) on the Unit. The pinouts are as follows: T1 (RJ-48C) 10Base-T Ethernet The 10Base-T Ethernet (female) port to connect to a remote management tool...
Page 24 - Local and Remote Management Option; Setting up a CLI connection
20 Compact T1 - Release 6.1 Quick Start Local and Remote Management Option Local and Remote Management Option This Quick Start Guide will focus on CLI and DIP switches. If you need further information on other management options, please refer to the Compact T1 User Manual. l Local using CLI, Telnet,...
Page 25 - Configuration
Compact T1 - Release 6.1 21 Quick Start Configuration Configuration The following basic setups and upgrades for the Compact T1 are shown below using CLI. For more information on CLI commands and configurations, see the Compact T1 User Manual. l Initial Setup l Set Up Security l Set Up a DS1/T1 l Set...
Page 26 - Initial Setup; Command
22 Compact T1 - Release 6.1 Quick Start Configuration Initial Setup Use the following commands for your initial setup, for further information see the specific command listed in this chapter. Set Up Security Use the following commands to set up the security on the Compact T1. See the set user comman...
Page 27 - Set Up a DS0/Channel
Compact T1 - Release 6.1 23 Quick Start Configuration Set Up a DS1/T1 Use the following commands to set up a DS1. See the set (ds1) command for more details. Set Up a DS0/Channel Use the following commands to set up a DS0. See the set (ds0) command for details. Command Description set {slot:port} up...
Page 28 - Set Up an Analog Port
24 Compact T1 - Release 6.1 Quick Start Configuration Set Up an Analog Port Use the following commands to set up an analog port. Command Description set {slot:port} up Activate the port. See set (ds1) command for details. set {slot:port} signal {dpt|gs| gsrb|gsw|gswrb|ls|lscpd|lsrb} Set the signalin...
Page 30 - Establish a Static Channel Connection
26 Compact T1 - Release 6.1 Quick Start Configuration Establish a Static Channel Connection Use the following commands to establish a static channel connection. Set Up a ISDN BRI Service Use the following commands to set up a ISDN BRI Service. See the set (bri) command for details. Command Descripti...
Page 31 - Set Up the OCU-DP Card
Compact T1 - Release 6.1 27 Quick Start Configuration Set Up the OCU-DP Card The following is a basic setup for the OCU-DP card. Command Description set {ocudp-addr} baud {2400|4800|9600|19200|38400| 56000*|64000} Set the OCU-DP Baud rate. Where ocudp-addr = {slot:port} of the OCU-DP card to apply s...
Page 32 - Change the IP Address of the DS0 Management Channel
28 Compact T1 - Release 6.1 Quick Start Configuration Set Up a V.35 Port Use the following commands to set up a V.35 port. See the set (v35) command for details. Change the IP Address of the DS0 Management Channel Use the following commands to change the IP over DS0 Management Channel for the Compac...
Page 33 - Upgrade the Controller Software
Compact T1 - Release 6.1 29 Quick Start Configuration Upgrade the Controller Software Use the following commands to determine the system software level, then upgrade the software to the latest version. Upgrade the Router (IP or CMG) Software Use the following commands to determine the Router card so...
Page 34 - Controller Cards; T1 Controller Card; Dip Switches; Switch Function Description
30 Compact T1 - Release 6.1 Quick Start Controller Cards Controller Cards T1 Controller Card Dip Switches On the front of the T1 Controller card on the Compact T1 are DIP switches used to configure the Compact T1 locally. Switch Function Description ACO Alarm Cut Off 0 = Alarm contacts enabled (clos...
Page 35 - LEDs; LED
Compact T1 - Release 6.1 31 Quick Start Controller Cards LEDs The T1 Controller has a set of six LEDs you can use to troubleshoot your Compact T1. The table below describes each LED. LED State Description MAJOR Off No major alarms present Red Major alarm present MINOR Off No minor alarms present Yel...
Page 36 - Power Supplies
32 Compact T1 - Release 6.1 Quick Start Power Supplies Power Supplies 115 VAC/-48 VDC Power Supply The power supply card has two LEDs, as described in the table below. LED State Description AC Input Off AC input missing or failure Green AC input present Battery Off Battery input not used Green Batte...
Page 37 - Service Cards; FXO Card; DIP Switch Settings
Compact T1 - Release 6.1 33 Quick Start Service Cards Service Cards FXO Card DIP Switch Settings The DIP switches on the FXO card control all eight channels. In order to apply different settings to channels on the same card, use the CLI. LEDs Each port on the FXO card has its own LED, as described i...
Page 38 - FXS Card
34 Compact T1 - Release 6.1 Quick Start Service Cards FXS Card DIP Switch Settings Each FXS card contains ten DIP switches that can be used to select signaling options for all eight channels. LEDs Each port on the FXS card has its own LED, as described in the table below. Switch Function Description...
Page 39 - ISDN BRI Card
Compact T1 - Release 6.1 35 Quick Start Service Cards ISDN BRI Card There is an LED for each ISDN BRI on a card, as described in the table below: OCU-DP Card There are two LEDs for each channel on the OCU-DP card. The function for each LED is listed below: State Description Off Line U-interface is a...
Page 40 - Quad T1 Card
36 Compact T1 - Release 6.1 Quick Start Service Cards Quad T1 Card Each channel on the Quad T1 card has two LEDs. The description of the top LED is shown below, the bottom LED is not used with this application. V.35/V.54 Card Each V.35 port has its own LED, as shown in the table below. State Descrip...
Page 41 - CMG Router Card
Compact T1 - Release 6.1 37 Quick Start Service Cards CMG Router Card The following chart describes each LED, and it’s state, of the CMG Router card. LED State Description CRD Off Loss of power Green No current alarms Red Alarm state active. See alarm log for cause Red Flashing Self-test or Boot in-...
Page 42 - IP Router Card
38 Compact T1 - Release 6.1 Quick Start Service Cards IP Router Card The following chart describes each LED, and it’s state, of the Router card . LED State Description CRD Off Loss of power Green No current alarms Red Alarm state active. See alarm log for cause Red Flashing Self-test or Boot in-proc...
