BenQ PB9200 - Manual

Part Names 3 Part Names Projector Elevator button Elevator foot Remote sensor Lens cap Lens The picture is projectedfrom here. Filter cover An air filter is inside. RGB port M1-D port BNC port AUDIO IN 1 port AUDIO IN 2 port CONTROL port NETWORK port AUDIO IN R/L port VIDEO IN port S-VIDEO port COMP...

Part Names 4 Control Buttons STANDBY/ON button and STANDBY/ON indicator TEMP indicator LAMP indicator LENS SHIFT buttons INPUT dial SEARCH button M1-D indicator RGB indicator BNC indicator COMPONENT indicator S-VIDEO indicator VIDEO indicator ZOOM buttons FOCUS buttons KEYSTONE button MENU button RE...

Setting Up 5 Setting Up Arrangement WARNING • Before installation, make sure that the projector is turned off and the power code is disconnected. • Do not set up and move the projector, while it is hot. • Install the projector in a suitable environment according to instructions of the “User’s Manual...

Setting Up 6 Adjusting The Projector's Elevator WARNING • Do not touch about the lens and ventilation openings during use or immediately after use to prevent a burn. CAUTION • To prevent damaging the projector and injuring yourself, always hold the projector whenever using the elevator buttons to ad...

Setting Up 7 Connecting Your Devices WARNING • Whenever attempting to connect other devices to the projector, read thoroughly the "User's Manual - Safety Guide", this manual and the manual of each device to be connected. Incorrect connecting could result in fire or electrical shock. CAUTION ...

Setting Up 8 Please refer to the following (for example) for connecting your devices. See the rear of the projector.You can see the ports. Examples of connection with a computer Computer Projector ■ If using a M1-D input (to mouse control) ■ If using a BNC input INTER INPUT M1-D RGB BNG S-VIDEO STAN...

Setting Up 9 Examples of connection with a VCR/DVD Player VCR/DVD Player Projector ■ If using a s-video signal ■ If using a component signal ■ If using a SCART RGB input VIDEO R-AUDIO IN-L S-VIDEO BNC RGB AUDIO IN1 AUDIO IN2 RGB OUT AUDIO OUT R/C R /P R G/Y B/C B /P B H V Y CONTROL NETWORK CR/PR Ca/...

Setting Up 10 Connecting to a monitor Monitor Projector Connecting to a speaker (with amplifier) Speaker Projector Connecting The Power Supply WARNING • Use extra caution when connecting the power cord as incorrect or faulty connections may result in fire and/or electrical shock. Please adhere to th...

Remote Control 11 Remote Control About The Laser Pointer WARNING • The laser pointer of the remote control is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people. The laser beam can cause vision problems. CAUTION • Use of controls ...

Remote Control 12 Operating The Remote Control CAUTION • Do not disassemble the remote control. • Do not place the remote control near the projector’s lens, fan, or vents. • Do not drop or otherwise expose the remote control to physical impact. • Do not get the remote control wet or place it on wet ...

Remote Control 13 Using The Remote ID Feature This is the function to properly use when you use two or three same type projectors at the same time. This function should be used com-bining a setup of a projector. 1. Set the ID number to the projector beforehand, referring to the item “IR REMOTE ID” o...

Power ON/OFF 14 Power ON/OFF WARNING • When the power is ON, a strong light is emitted. Do not look into the lens or vents of the projector. NOTE • Turn the power on/off in right order. Please power on the projector before the connected devices. Power off the projector after the connected devices. T...

Operating 15 Operating Selecting An Input Signal 1. Select an input signal. ■ Using the INPUT dial Turn the INPUT dial of the projector. Turning the dial cycles through the input ports as shown below. Select the signal you wish to project. ■ Using SEARCH button Press the SEARCH button of the project...

Operating 16 Selecting The Aspect Ratio 1. Press the Aspect button to toggle between the modes for aspect ratio. ■ At a M1-D signal memo NORMAL keeps the original aspect ratio of the input signal. ■ At a RGB signal (not M1-D) ■ At a video signal / no signal memo At a HDTV signal of 1125i or 750p, on...

Operating 17 Adjusting The Picture Position 1. Press the POSITION but-ton. As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position. 2. Use the cursor buttons / / / to adjust the position. memo When you want to ini- tialize the position, press the RESET bu...

Operating 18 Adjusting The Volume 1. Press the VOLUME button. As illustrated on the right, a dialog will appear on the screen to aid you in adjust-ing the volume. 2. Use the cursor buttons / to adjust the volume. 3. Press the VOLUME button again to close the dialog and complete this operation. memo ...

Operating 19 Freezing The Screen 1. Press the FREEZE button. As illustrated on the right, a dia-log will appear on the screen, and the screen will freeze at the current image. 2. Press the FREEZE button again to restore the screen to normal. The icon “||” will change to the icon “ 4 ”. And after a c...

Operating 20 Displaying The Child Window memo This feature called "PinP (Picture in Picture)" is available only when a RGB signal is selected to main screen. 1. Press the PinP button. The child window with a picture of a video signal will appear. 2. Press the PinP button again to change the ...

Multifunctional Settings 21 Multifunctional Settings Using The Menu Functions This projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO, SCREEN, OPTION and NETWORK. Each of these menus is operated using the same meth-ods. The basic operations of these menus are as follows. 1. P...

Multifunctional Settings 22 MAIN Menu With the MAIN menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item Description BRIGHT Adjust the brightness using the 5 / 6 buttons. : Light Dark CONTRAST Adjust the contra...

Multifunctional Settings 23 PICTURE-1 Menu With the PICTURE-1 menu, the items shown in the table below can be performed. Perform each operation in accor-dance with the instructions in the table below. (This table is continued to the following page.) Item Description GAMMA Select a gamma mode using t...

Multifunctional Settings 24 PICTURE-1 Menu (continued) Item Description MY MEMORY Select a command to load or save using the 5 / 6 buttons, and then press the (or the ENTER) button to perform the function.: This projector has 4 numbered memories for adjustment data. Per-forming the SAVE1, SAVE2, SAV...

Multifunctional Settings 26 INPUT Menu With the INPUT menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. (This table is continued to the following page.) Item Description COLOR SPACE Select a color space mode usin...

Multifunctional Settings 28 AUTO Menu With the AUTO menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. (This table is continued to the following page.) Item Description ADJUST Pressing the 4 (or the ENTER) button ...

Multifunctional Settings 29 AUTO Menu (continued) Item Description SEARCH Select the TURN ON or the TURN OFF using the 5 / 6 buttons. : TURN ON TURN OFF When the TURN ON is selected, detecting no signal cycles through input ports and displays the picture of retrieved signal. memo When the TURN ON is...

Multifunctional Settings 30 SCREEN Menu With the SCREEN menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. (This table is continued to the following page.) Item Description BLANK Select a type of the BLANK screen ...

Multifunctional Settings 31 SCREEN Menu (continued) How to register your picture as the MyScreen Item Description MESSAGE Select the TURN ON or the TURN OFF using the 5 / 6 buttons. : TURN ON TURN OFF When the TURN ON is selected, the following message function works. The message of the AUTO IN PROG...

Multifunctional Settings 32 OPTION Menu With the OPTION menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. (This table is continued to the following page.) Item Description VOLUME Adjust the volume using the 5 / 6...

Multifunctional Settings 33 OPTION Menu (continued) Item Description SERVICE Pressing the 4 (or the ENTER) button calls the SERVICE menu. SERVICE Menu Select an item using the 5 / 6 buttons, and press the 4 (or the ENTER) button to per form each function. :FANSPEED AUTO ADJUST LENS TYPE LENS LOCK FA...

Multifunctional Settings 34 NETWORK Menu This projector provides the NETWORK function. If you use this function, please set up the projector according to the Network environment in which you use it. memo If DHCP function on your Network is activated, the following operation is not normally required,...

Network Setting Up 35 Network Setting Up This projector provides the NETWORK function. When you start to use this function, please consult your dealer for further information. To start, connect the NETWORK port to a gateway device via a CAT-5 cable, then set up the projector according to the Network...

Lamp 36 Lamp WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or ...

Lamp 37 Replacing The Lamp If the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. 1. Turn off the projector, and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes. 2. Contact your dealer to prepare a new lamp. Tell the dealer yo...

Air Filter 38 Air Filter WARNING • Please carefully read the “User’s Manual - Safety Guide. • Before caring, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently. • Use only the air filter of the specified type NJ080...

Other Care 39 Other Care WARNING • Please carefully read the “User’s Manual - Safety Guide”. • Before caring, make sure the power switch is off and the power cable is not • plugged in. • Be cautious of high temperature. Do not touch about the lens and ventilation openings during use or immediately a...

Troubleshooting 40 Troubleshooting Related Messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below. If the same message is displayed after the treatment, or if a message other than ...

Troubleshooting 41 Related Messages (continued) Message Description CLEAN THE AIR FILTER POWER OFF FIRST, THEN CLEAN THE AIR FILTER. AFTER CLEANING THE AIR FILTER, RESET THE FILTER TIMER. The time the filter timer has counted has reached 100 hours. Please clear or change the air filter by referring ...

Troubleshooting 42 Regarding The Indicator Lamps Lighting and flashing of the STANDBY/ON indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table. If the same indication is displayed a...

Troubleshooting 43 Regarding The Indicator Lamps (continued) STANDBY/ ON indicator LAMP indicator TEMP indicator Description Lighting in Red Blinking in Red Turned off Either there is no lamp and/or lamp cover, or either of these has not been properly fixed. Please turn the power off, and allow the ...

Troubleshooting 44 Phenomena That May Easily Be Mistaken For Machine Defects WARNING • Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immedi...

Troubleshooting 45 Phenomena That May Easily Be Mistaken For Machine Defects (continued) Phenomenon Cases not involving a machine defect Referenc e pages Pictures are displayed, but no sounds are heard. The signal cables are not correctly connected. Correctly connect the connection cables. 8 , 9 The...

Warranty And After-Service 46 Warranty And After-Service If a problem occurs with the equipment, first refer to the “Troubleshooting” and run through the suggested che cks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition...

Specifications 47 Specifications NOTE • This specifications are subject to change without notice. Item Specification Product name Liquid crystal projector Liquid crystal panel Panel size 2.5 cm (0.99 type) Drive system TFT active matrix Pixels 786,432 pixels (1024 horizontal x 768 vertical) Lens Zoo...