Page 3 - AFETY PRECAUTIONS; using multiple components, make sure all units are grounded
S AFETY PRECAUTIONS Fuse amplifiers power wire at the battery. Be sure to fuse the power wire within 12” of the car's battery. This will protect the car's battery in case of a short circuit between the power amplifier and battery. THIS IS A MUST, the amplifier's built-in fuse will only protect the p...
Page 4 - EATURES AND BENEFITS; Bazooka
F EATURES AND BENEFITS DC Offset Protection This circuit protects the output of the amplifier against DC voltage. If for some reason DC voltage is detected at the output stage, the amplifier will shut down protecting the speakers from direct current. Short Circuit Protection The circuit protects the...
Page 5 - Allowing for integration with “Factory Sound Systems”.; Stable To 2 Ohm Stereo Mode
Bass Boost For added low frequency performance the amplifiers are equipped with a variable 0~12 dB bass boost @ 45Hz. Line Out (ELA150.1, ELA300.1 and ELA / MAA500.1 Only) One set of full range line outputs have been provided for convenient connection to additional amplifiers in the system. Power Fu...
Page 6 - OUNTING LOCATION; mounting locations are in the trunk or under the seat.
M OUNTING LOCATION Before you start the installation, it will be necessary to find a mounting location for the amplifier. Find a location in which the amplifier will receive adequate ventilation in order to dissipate the heat it develops during operation. Two popular mounting locations are in the tr...
Page 7 - OWER CONNECTIONS; Connect the amplifier to the car's battery.; connection can also be made to the radio’s Power Antenna wire.
CAR BATTERY +12V CAR BATTERY +12V - - + + P OWER CONNECTIONS SPEAKERS BRIDGED AUX OUTPUT +12V REM 20A 20A AUX 7.5A 20A AMP GND IN-LINE POWER FUSE MOUNTED WITHIN 12" FROM BATTERY RECOMMENDED IN-LINE POWER FUSE MOUNTED WITHIN 12" FROM BATTERY RECOMMENDED (NOT PROVIDED) (NOT PROVIDED) 94.7 94.7...
Page 8 - IGNAL CONNECTIONS; SIGNAL CONNECTIONS; SIGNAL CONNECTIONS; the RCA input terminals of the amplifier.
POWER BASS BOOST 12dB 0dB X-OVER 400Hz 60Hz LEVEL INPUT HI INPUT REMOTE R L MAX MIN FILTER LOW FLAT HI ELA150.1, ELA300.1 AND ELA / MAA500.1 SIGNAL CONNECTIONS LL R R POWER BASS BOOST BASS BOOST 12dB 12dB 0dB 0dB X-OVER X-OVER 400Hz 400Hz 60Hz 60Hz LEVEL INPUT HI INPUT HI INPUT REMOTE CH1 CH2 CH3 CH...
Page 11 - SPEAKER CONNECTIONS; PEAKER CONNECTIONS; FOUR CHANNEL SPEAKER CONNECTIONS
SPEAKER +12V REM 15A 15A 15A 15A FUSE GND ELA150.1, ELA300.1 AND ELA /MAA500.1 SPEAKER CONNECTIONS 4 Ohm Speaker (2 Ohm Minimum) 4 Ohm Speaker (2 Ohm Minimum) Make the speaker connections using speaker wire that is at least 16 gauge or heavier. As with any audio component, proper phasing of the ampl...
Page 12 - right and left RCA connections must be made.; In the bridged mode, the amplifier must see a 4 Ohm load or higher.
BRIDGED CH 1 CH 2 CH 4 CH 3 AUX OUTPUT +12V REM GND 20A AUX 7.5A 20A AMP + - + - + - + - 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker 4 Ohm Speaker SPEAKERS BRIDGED AUX OUTPUT +12V REM 20A 20A AUX 7.5A 20A AMP GND + + 4 Ohm Speaker 4 Ohm Speaker TWO CHANNEL BRIDGED SPEAKER CONNECTIONS FOUR CHANNEL BRID...
Page 13 - recommended that you seek professional advice from your BAZOOKA
SPEAKERS BRIDGED AUX OUTPUT +12V REM 20A 20A AUX 7.5A 20A AMP GND CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifier to overheat ...
Page 14 - To avoid
POWER BASS BOOST 12dB 0dB X-OVER 400Hz 60Hz LEVEL INPUT HI INPUT REMOTE R L MAX MIN FILTER LOW FLAT HI R EMOTE BASS CONTROL MODULE (OPTIONAL) Before connecting the remote, it will be necessary to find a mounting location that will be easy to access for adjustment. Once you select your mounting locat...
Page 15 - DJUSTING THE X-OVER AND BASS; Fine tune the amplifier's input sensitivity.; INE TUNE THE SYSTEM; LEVEL; MAX; FILTER; BASS
. (Please note: If you intend to use the amplifier in the Tri-mode configuration, it is necessary to set the crossover control to the “FLAT” setting in order to receive full range output) The “EL” amplifiers are equipped with a built-in variable crossover network allowing you to select the crossover...
Page 16 - ROUBLE SHOOTING THE SYSTEM
T ROUBLE SHOOTING THE SYSTEM We have put together this trouble-shooting guide if you experience problems after installing the amplifier. Please keep in mind that the majority of problems incurred are caused by improper installation and not the equipment itself. In addition, there are many components...
Page 17 - PECIFICATIONS
16 S PECIFICATIONS ELA60.2 ELA100.2 ELA150.1 Size (L x W x H) 8 Max Power 300W 500W 300W Output Power @ 14.4 VDC : 4 ohm 70W x 2 115W x 2 100W x 1 2 ohm 95W x 2 165W x 2 150W x 1 Bridged 4ohm 190W x 1 330W x 1 N/A Frequency Response + - 1dB 20Hz-22KHz 20Hz-22KHz 20Hz-130Hz S/N Ratio (A-weight) >9...
Page 18 - LIMITED WARRANTY; What is not covered: This warranty does not cover the following:
17 LIMITED WARRANTY Southern Audio Services, Inc., warrants all products to be free from defects in material and workmanship for a period of one (1) year from the date of purchase; the Reference Series is warranted for a period of two (2) years from date of purchase. In the event the product is not ...
Page 19 - How to obtain warranty services:; complete this section and retain for your records.
18 How to obtain warranty services: 1. You are responsible for delivery of the product to an authorized BAZOOKA® dealer or contact SAS at 1-800-THE TUBE for a Return Authorization number. The Return Authorization number must be clearly written on the outside of the box. Freight must be prepaid to SA...