Azden Enhanced Broadcast Performance UHF Wireless System - Manual
Azden Enhanced Broadcast Performance UHF Wireless System – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – D. Input Level Adjustment
- Page 4 – the correct polarity.; DO NOT FORCE THE BATTERY INTO THE COMPART-; Azden does not recommend the use of rechargeable batteries.; SETTING THE TRANSMITTING FREQUENCY ON THE 1201XT; two screens below appears.; TABLE OF CONTENTS; iii
- Page 5 – POWERING THE 1201XT TRANSMITTER
- Page 7 – Powering the 1201BT Transmitter; DO; Azden does not; SETTING THE TRANSMITTING FREQUENCY ON THE 1201BT; l m n o
- Page 8 – 201URX/Si Top panel display and operation:; Initial MODE display:
User’s Guide
1201URX/AB • 1201URX/VM • 1201URX/Si
1201BT • 1201XT
ENHANCED BROADCAST PERFORMANCE
UHF WIRELESS SYSTEM
1201URX/AB - 1201URX/Si - 1201URX/VM
RF Carrier Frequency Range
188 steps ~ 638.125 - 661.875 MHz
MicroComputer Controlled PLL Synth.
Noise Reduction
Expander (THAT)
Effective Operating Range
200 - 300 ft ~ 60 - 100m
Frequency Response
50 - 15kHz (± 1.5dB)
RF Sensitivity
(12dB SINAD) 1.2μV
Adjacent Channel Selectivity
> 70dB (± 250kHz)
Image Rejection
> 93dB
IF Rejection
> 93dB
Audio THD
< 0.8%
Audio Output
40dBm ± 40kHz Deviation (-20dBm ± 40kHz Deviation for 1201URX\Si)
Output Impedance
600Ω (300Ω for 1201URX\Si)
Signal/Noise Ratio
> 62dB (± 5kHz Deviation) “A” Weighted
Power Requirements
11 - 15V DC @ 220mA (10 - 17V DC @ 200mA for 1201URX\Si)
Dimensions
68W x 84H x 18D mm- 1201URX/Si insertion
93W x 119H x 49D mm - 1201URX/AB
82W x 150H x 60D mm - 1201URX/VM
Operating Temperature Range
-50
0
- +122
0
F ~ -10
0
- +50
0
C
Weight
8.8 ounces ~ 250g for 1201URX/Si
15.87ounces ~ 450g for 1201URX/AB
26.45ounces ~ 750g for 1201URX/VM
1201BT
Output Power
30mW
Max Modulation Sensitivity
-4dBm
MIC Level / Imped.
-56dBm (± 5kHz Deviation)
Power Requirements
3V DC (2 “AA” Alkaline) @ < 150mA
Dimensions
2.48 (W) x 3.86 (H) x 1.12 (D) inches
63 (W) x 98 (H) x 28.5 (D) mm
Weight w/Battery
6.35 ounces ~ 180g
1201XT
Output Power
30mW
Max Modulation Sensitivity
+20dBM ~ 0dBm
MIC Level / Imped. (Dynamic)
-60dBm / 2.2kΩ (± 5kHz Dev.)
Phantom Power
48V ±2V @ 2mA
Power Requirements
3V DC (2 “AA” Alkaline) @ < 180mA - 290 mA w/Phantom Power ON
Dimensions
1.57 (W) x 4.49 (H) x 1.57 (D) inches
40 (W) x 114 (H) x 40 (D) mm
Weight w/Battery
6.35 ounces ~ 180g
Due to constant improvements, specifications are subject to change without notice.
Licensing
Licensing of this, or any Azden wireless equipment is the user’s responsibility. The ability to receive a license depends largely on the user’s classification, applica-
tion and frequency. Contact the appropriate agency (FCC in the USA) for further information.
SPECIFICATIONS
Azden Corporation, 147 New Hyde Park Road, P.O. Box 10, Franklin Square, NY 11010
tel - 516.328.7500 • fax - 516.328.7506 • email - [email protected]
© 2010 Azden Corporation
Printed in USA
P1030-02
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
INTRODUCTION Thank you for selecting the Azden 1201 Series for your portable/ENG on-camera UHF wireless needs. We are confident that these compo- nents will perform beyond your expectations. For over 50 years, Azden Corporation has been creating technologically advanced products. By taking advantage...
POWERING THE 1201XT (continued) in the illustration. The compartment is deigned to ease battery insertion - With the correct polarity. DO NOT FORCE THE BATTERY INTO THE COMPART- MENT. Azden does not recommend the use of rechargeable batteries. SETTING THE TRANSMITTING FREQUENCY ON THE 1201XT Before ...
RECEIVER SETUP (1201URX/AB and 1201URX/VM) The 1201URX/AB is a specially developed model that integrates the Anton Bauer “Gold Mount” to power the receiver. The 1201URX/VM is a specially developed model that integrates the IDX battery-mount to power the receiver. All of the functions and controls of...
