Atlantic 567150 - User Manual

30 We recommend that you place the device face down on the floor, taking care to protect its frontsurface from scratches. U NLOCKING THE DEVICE ’ S HANGING FRAME F IXING THE HANGING FRAME TO THE WALL Take a flat- bladed screw-driver and liftthe slider, takingcare not tobend it. While keeping the sli...

31 Wiring diagram for the heating panel - Cut off the power supply and connect the wires as shown in the following diagram: - You can connect the pilot wire if your home is equipped with a programming unit or controller. In this case, make the following checks according the selected mode ( Comfort, ...

32 L OCKING THE DEVICE ONTO THE HANGING FRAME Position the tilted device on brackets S1 . Pivot the device upwards and lift it toposition it on brack-ets S2 . Lower the device onto the hanging frame. Aclick tells you that the device is fastened andlocked in place. 1 2 3 S1 S2 CLIC To unlock the devi...

33 A absence and presence detector B Airing function C Programming / Ste the correct time and day D Increase the temperature / Scroll E Turn on / Change heating modes – scroll / Standby F Lower the temperature / Scroll G Consumption indicator function Operation Control box The different displays Rem...

34 Use A CTIVATING THE SCREEN If the screen is not lit up, press any button to activate the screen lighting. T URNING ON YOUR DEVICE When first turned on, the device is set to Comfort mode at 19°C . P UTTING YOUR DEVICE IN STANDBY MODE To turn on your device, press thePower on key ( E ). The device ...

35 C HOOSING YOUR HEATING MODE You can run your device in several modes: - Comfort mode ( ) which enables you to have the right ambient temperature. - Eco mode ( ) which enables you to lower the temperature in your room when you will be away from your home for a long time or during the night, especi...

36 H EATING YOUR ROOM : HOW TO USE COMFORT MODE The advised Comfort temperature is 19°C.The Comfort mode ranges from 12.5°C to 28°C. This mode enables you to have the ambient temperature you desire in your room. The consumptionindicator lights enable you to optimise your setting ( see page 48 ). D E...

38 You can program your Comfort and temperature times either by using one of the threeprestored programs, or by connecting the pilot wire to a programming control ( Pilot wire (FP) mode is the default setting - refer to your programming control’s manual ) You can connect several devices to one progr...

39 H OW TO SET THE DAY OF THE WEEK AND TIME ? Before programming the device, you must set the device to the correct time or make sure that thesystem day and time is correct. GB To set the day of the week andthe time, hold the Programmingkey ( C ) down for several sec- onds. The letters on the screen...

41 H OW TO ASSIGN A DAILY PROGRAM ? a- You want to keep the selected program – Monday in the example b-You want to change the selected program – Monday in the example Two solutions are possible : a- you want to keep the selected program, b- you want to change the selected program. GB To access the d...

43 A BSENCE OF MORE THAN 24 HOURS : USING THE FROST PROTECTION MODE The Frost Protection temperature is preset to 7°C (±3° C) and cannot be changed. H OW TO ACTIVATE THE F ROST P ROTECTION MODE ? GB Press the scroll key ( E ) until the selection arrow is on the FrostProtection mode. The mode selecti...

44 The function enables you to lower the temperature setting for your room automatically, as soon asyou leave it. H OW TO USE THE ENERGY - SAVING FUNCTIONS : A BSENCE AND PRESENCE DETECTION These functions enable your device to adapt itself to your daily life without your having to concernyourself w...

46 The function enables you to stop the device from heating and to start heating again automaticallywhen you are airing your room, thereby saving you energy. We do not recommend the use of the Airing function in corridors and rooms located close toan entrance door from outside your home or from the ...

49 To avoid the control panel being used inopportunely, we advise you to lock it. L OCKING THE CONTROLS L OCKING THE CONTROL PANEL You can also lock the control panel using the screw provided. H OW TO LOCK THE CONTROLS ? H OW TO UNLOCK THE CONTROLS ? GB To lock the controls, press thefollowing keys ...

50 It is possible de return to the standard settings for your device. R ETURNING TO THE STANDARD FACTORY SETTINGS To maintain your device’s performance, you must dust it approximately twice a year. Never use abrasive products or solvents. M AINTENANCE C ALIBRATE THE TEMPERATURE Depending on your ins...

51 P ROBLEM ENCOUNTERED C HECKS TO BE MADE The heating light flas-hes The temperature probe is disconnected or is faulty.Contact your installer. The device does notheat. Make sure that the mode is activated.If you are operating under programming, check that the programmer is inCOMFORT mode. Ensure t...

52 P ROBLEM ENCOUNTERED C HECKS TO BE MADE The device’s surfaceis very hot. It is normal for the device to be hot when it is operating; the maximum sur-face temperature is restricted in accordance with the NF electrical perfor-mance standard. However, if you think that your device is still too hot, ...

53 - The guarantee period is two years from the date of installation or purchase and may not exceed 30 months from the date of manufacture in the absence of a receipt. -The guarantee covers the replacement and supply of components recognised as being defective, excluding any damages or interest. - T...