ATD ATD-6567 - Manual

PARTS LIST AND DIAGRAM FOR:

MASKER

MODEL NO:

ATD-6567

PARTS LIST

ITEM

PART NO.

DESCRIPTION ITEM

PART NO. DESCRIPTION

ITEM

PART NO.

DESCRIPTION

1.

PRT6567-01 Frame, Side

9. PRT6567-09 Mounting Bracket

18.

PRT6567-18 Wing Nut

2.

PRT6567-02 Top Handle

11.

PRT6567-11 Washer, 5/16"

20.

PRT6567-20 Tape Reel

3.

PRT6567-03 Paper Cutter 12.

PRT6567-12 Screw, 5/16 x 1-1/2"

21.

PRT6567-21 Hub

4.

PRT6567-04 Cross Tube

13.

PRT6567-13 Nut, 1/4"

22.

PRT6567-22 Bolt, 1/4 x 3-1/2"

5.

PRT6567-05 Paper Retainer 14.

PRT6567-14 Washer, 1/4"

23.

PRT6567-23 Paper Bar Spring

6.

PRT6567-06 Paper Washer 15.

PRT6567-15 Screw, 1/4 x 1-1/2"

24.

PRT6567-24 Knob

7.

PRT6567-07 Screw, 3/16 x 1/2" 16.

PRT6567-16 Foot

PRT6567-HK Hardware Kit

8.

PRT6567-08 Paper Bar

17.

PRT6567-17 Paper Spring

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of product.

ATD-6567

IMPORTANT:

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1. SAFETY INSTRUCTIONS

• Ensure the dispenser is on a reasonably flat, level floor or securely wall mounted before loading.

• Be aware that the paper cutting blade is sharp - handle with care.

•

DO NOT

sit or stand on the dispenser.

•

DO NOT

use the dispenser for any purpose other than that for which it was designed.

2. CONTENTS & ASSEMBLY

2.1. Contents

2.1.1. Check the contents against the list below and if any items are missing or damaged contact your supplier immediately.
• Paper Cutter

• Paper Spring

• Base x 2

• Hub x 2

• Frame Side x 2

• Top Handle

• Cross Tube

• Paper Bar

• Tape Reel x 2

• Knob

• Bag of fittings

Fittings:

• Foot x 4

• Spring x 2

• Slide Ring x 2 • Paper Washer, x 2 • Washer, 1/4" x 16

• Nut, 1/4" x 4

• Wing Nut, 1/4" x 4 • Screw, 3/16 x 1/2" x 4 • Screw, 1/4 x 1-1/2" x 4 • Bolt, 1/4 X 3-1/2" X 2

• Screw, 5/16 x 1-1/2" x 4 • Washer, 5/16" x 4 • Hub x 2

2.2. Assembly

Note: Numbers in brackets refer to item numbers in the Parts List.

2.2.1. If dispenser is to be free standing fit the four feet (16) to the side frames (1).

2.2.2. If the dispenser is to be bench or wall mounted fit the two bases (9) to the rear legs of the side frames (1),

using 5/16" x 1-1/2" screws (15), 1/4" washers (14) and 1/4" nuts (13). Fit two of the feet (16) to the front

legs of the side frames (1).

2.2.3. Attach the top handle (2) to the top of the side frames (1) using 5/16 x 1-1/2" screws (12) and 5/16"

washers (11).

2.2.4. Attach the two side frames (1) to the cross tube (4) using 5/16 x 1-1/2" screws (12) and 5/16" washers (11).

Do not fully tighten screws at this stage.

2.2.5. Attach paper spring (17) loops to either end of the paper cutter (3), as shown in fig.1.

2.2.6. Fit paper cutter (3) to upper holes in front legs of side frames (1) using 1/4 a 1-1/2" screws (15), 1/4" washers (14) and 1/4" nuts (13).

2.2.7. Tighten all screws/nuts.

2.2.8. Insert 1/4 x 3-1/2" bolts (22) through front legs of side frames (1) and tighten in place using 1/4" washers (14) and 1/4" nuts (13).

2.2.9. Thread a wing nut (18) onto each of bolts (22) with the wings towards the frame leg.

2.2.10. Slide washer (14) and hub (21) onto each bolt (22) and then fit tape reels (20) onto hubs (21) with open sides towards side frame (1) legs.

2.2.11. Retain tape reels with washer (14) and wing nut (18).

2.2.12. Fit paper washers (6), paper bar spring (23) and paper retainers (5) to paper bar (8) as shown in fig.2. Insert 3/16 x 1/2" screws (7)

into paper retainers (5).

2.2.13. Locate paper bar (8) between bars of side frames (1) and retain with knob (24).

3. USE

3.1. Remove paper bar (8) from frame and remove washers (6), springs (23) and retainers (5).

3.2. Slide paper bar (8) through centre of masking paper roll so that, when reinstalled in frame,

paper will come from top of roll towards front of dispenser.

3.3. Replace washers (6), springs (23) and retainers (5), as shown in fig.2, at each end of roll.

If two narrow rolls are used fit one spring and paper washer per roll and use the two extra paper retainers.

3.4. Refit paper bar, complete with paper roll, to frame assembly. Position roll in centre of bar and fix in place by tightening screws (7) in

paper retainers (5).

3.5. Thread leading edge of paper between paper spring (17) and guide edge of paper cutter (3), see fig.1.

3.6. Press masking tape rolls onto tape reels (20) so that tape leaves bottom of rolls towards the rear of the dispenser. Rolls may be

positioned relative to the masking paper edges by adjusting wing nuts (18).

PRT6567-HK (Hardware Kit) including PRT6567-05, 06, 07, 11, 12, 13, 14, 15, 16, 18, 21, 22 and 23