ATD ATD-112 - Manual

FEATURES

♦

Limits torque applied with reduced-friction release mechanism.

♦

Can be used with confidence in all automotive, aircraft, marine

and industrial applications.

♦

Lock ring prevents accidental change of torque setting.

♦

Pliable handgrip of soft Thermoplastic rubber protects painted

surfaces and simplifies use with greasy hands. Resistant to

mechanical damage and impervious to automotive fluids such

as gasoline, oil, kerosene, etc.

♦

Ratchet action requires only 10 degrees handle travel.

♦

Extra strength ratchet design for long life.

♦

May be used continually at maximum torque capacity.

♦

Wrench cannot be damaged by normal handling or dropping

from workbench.

♦

Mechanism protected from routine contamination.

♦

Finished with tough, durable chromium-nickel plating.

♦

All parts corrosion proofed.

♦

Wrench made of highest quality CR-MOLY steel.

SUGGESTIONS

Proper use of this professional torque wrench will give you

complete satisfaction in its performance and reliability. Following

are some helpful tips:

1. Greater torque accuracy is assured by gripping it properly.

Grasp the GRIP, not the SHAFT, and pull smoothly.

2. Each torque wrench is lubricated before leaving the factory. If it

has not been used for some time, it should be operated several

times to re-distribute the lubricant within the working

mechanism.

3. Never attempt to turn the GRIP when the LOCK RING is in the

"LOCK" position.

4. Never set for higher or lower torque values than those indicated

on your wrench.

5. For greater accuracy, clean all thread surfaces and remove any

burrs on the fasteners being used.

6.

WARNING

- Never use your torque wrench to apply more

torque than its rated capacity.

7. It is not necessary to return this wrench to its lowest calibrated

value after use unless it is to be stored for an extended period

of time.

DO NOT OVERTORQUE

CERTIFICATION

This torque wrench is certified to be calibrated prior to

shipment to accuracy of +/-4% in the right hand direction on

readings 20% to 100% of capacity. On readings below 20% of

capacity, the accuracy is +/- two scale increments.

LIMITED WARRANTY

If within 90 days from the date of purchase, this wrench fails

due to defects in

materials

or

workmanship

, we will repair

and recalibrate it free of charge. After 90 days and until one

year from the date of purchase we will repair any defect in

material or workmanship in the torque wrench free of charge.

This warranty does not include recalibration.

PROOF OF PURCHASE MUST BE INCLUDED WITH EACH

REQUEST FOR WARRANTY SERVICE.

For warranty service send the wrench to:

REPAIR AND CALIBRATION SERVICE

All torque wrenches should have periodic accuracy checks

and recalibration as required. This should be done at least

once a year or every 5000 torque application cycles,

whichever comes first.

Recalibration is also recommended after any abnormal

handling. For service send the wrench to one of the

Warranty Centers listed above of contact our Customer

Service department at (800)866-5287 for a list of additional

Approved Repair Centers.

REVISED/PRINTED IN USA APR 2014 FORM 6000M-90

ATD-112

INDUSTRIAL DUTY

MICRO-ADJUSTING

TORQUE WRENCH

OPERATING INSTRUCTIONS

1. STUDY THIS BOOKLET CAREFULLY

BEFORE ATTEMPTING TO OPERATE THIS

WRENCH.

2. NEVER APPLY MORE TORQUE THAN THE

MAXIMUM SCALE SETTING.

3. This Torque Wrench is designed for manual

tightening of threaded fasteners only. DO

NOT USE IT AS A NUT-BREAKER OR FOR

ANY OTHER PURPOSE.

4. Over torqued or defective fasteners and

sockets may suddenly break. Ratchets on

plain drives that are improperly engages,

worn out, damaged or over torqued, may

slip or break. TO PREVENT INJURY, KEEP

PROPER FOOTING AND BALANCE AT ALL

TIMES. DO NOT USE THE WRENCH IN

PLACES FROM WHICH YOU MAY FALL OR

SLIP OR AROUND ROTATING MACHINERY.

5. This wrench will not prevent you from

applying more torque than set, it is not a

torque limiting tool. Learn how different

amounts of torque “feel”, so you will reduce

the possibility of damage and/or injury due

to accidental over torquing.

6. APPLY FORCE TO THE GRIP ONLY. DO

NOT USE “CHEATER BARS” (A Piece of

pipe placed over the hand grip for more

leverage).

7. There are no user-serviceable components

inside the wrench. Disassembling the

wrench or making any adjustments will

result in the loss of accuracy, and will void

the warranty

.

In the U.S.A.

Angle Repair & Calibration

175 Angle Drive

Beckley, WV 25801

www.anglerepair.com

972-864-6762

In Canada

ATG Torque Repair

7631 Bath Road

Mississauga, ON L4T3T1

1-866-691-6212