ATD ATD-10556 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Table of Contents:
Page 2 – Induction
Page 3 – Important Safety Rules
Page 4 – Know Your Grinder; Water tray; Guards
Page 5 – Operating Instructions
Page 6 – cords. Always replace a damaged extension cord.; Eye shield mounting rod
Page 7 – Position the grinder on the workbench.; Eye Shield Installation; Eye shields must be installed before operating the bench grinder.
Page 8 – Fit an appropriately sized wrench on the spindle hex nut.
Page 9 – If the workpiece becomes hot, dip it into the water or oil to cool it.
Page 10 – coolant tray
Page 13 – PARTS DIAGRAM
Page 14 – AT
Loading the manual
1
ATD-10556 & ATD-10558
Bench Grinder
Instruction Manual
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 - Induction
2 Table of Contents SPECIFICATIONS --------------------------------------------------------------------------------------------------- 2 IMPORTANT SAFETY RULES------------------------------------------------------------------------------------ 3 KNOW YOUR BENCH GRINDER ------------------------------...
Page 3 - Important Safety Rules
3 Important Safety Rules DANGER!! Failure to observe any of the following instructions could result in severe personal injury to tool user and bystanders or cause damage to tool and property! WARNING! – Read, understand and observe all instructions in this manual before using or operating the tool f...
Page 4 - Know Your Grinder; Water tray; Guards
4 Know Your Grinder On/off switch Base – bolt-down area Water tray Guards Tool rest/work rest Bolt-down hole Plain eye shield
Page 5 - Operating Instructions
5 Operating Instructions Before You Start - Safety Always wear eye protection that complies with a recognized standard (for example: ANSI Z87.1) - (CSA or ANSI). Wear a mask or respirator when dust is generated. Keep bystanders out of the work area while operating the tool. WARNING! Always ensure th...
Page 6 - cords. Always replace a damaged extension cord.; Eye shield mounting rod
6 Use of Extension Cords USE ONLY THREE-WIRED EXTENSION CORDS that have 3-pronged plugs and 3-holed outlets that accept the tool’s plug. Repair or replace damaged or worn cords immediately. Be sure your extension cord is properly wired and in good condition. Do not use damaged extension cords. Alway...
Page 7 - Position the grinder on the workbench.; Eye Shield Installation; Eye shields must be installed before operating the bench grinder.
7 Before You Start – Assembly and Installation Mounting the Grinder to the Workbench Before attempting to use this grinder, it must be properly mounted to a workbench or grinding stand (ATD-10557). CAUTION! Bench grinders vibrate. Grinder movement during high-speed rotation may cause injury or damag...
Page 8 - Fit an appropriately sized wrench on the spindle hex nut.
8 NOTE: The eye shield should move freely when being adjusted, but stay in place when the locking knob is tightened. WARNING! Turn the power off and remove the plug from the outlet before changing the grinding wheels. When turning the grinder on with a newly installed wheel, DO NOT STAND IN FRONT OF...
Page 9 - If the workpiece becomes hot, dip it into the water or oil to cool it.
9 Tool Rest Adjustments and Installation Mount the tool rests to the work rest bracket using the knob and washers. Before tightening the knob, adjust the gap between the grinding wheel and the work rest to a maximum of 1/8” (3.2 mm). Tighten securely. Adjustments To prevent the workpiece from being ...
Page 10 - coolant tray
10 If the face of the grinding wheel is worn unevenly, becomes grooved, or is no longer smooth and flat, the wheel should be reshaped with a dressing tool (not supplied). If the diameter of the grinding wheel is no longer round, the wheel should be reshaped with a dressing tool or replaced. If the s...
Page 13 - PARTS DIAGRAM
Page 14 - AT
14 IT EM # O RD ER IN G PA RT # DE SC RI PT IO N SP EC Q TY IT EM # O RD ER IN G PA RT # DE SC RI PT IO N SP EC Q TY 1 PR T1 05 56 -0 1 PH IL IP S SC RE W + SP RI NG W AS HE R+ FL AT W AS HE R (B LA CK ) M 5x 12 6 29 PR T1 05 56 -2 9 FL AT W AS HE R (W HI TE ) D1 2 1 2 PR T1 05 56 -0 2 LE FT W HE EL...
