ARRI 416 - Manual - manualsarea.com

Page 2 - This page is left blank intentionally.

ARRIFLEX 416 Quick Guide 05/2006, Page 2 This page is left blank intentionally.

Page 3 - Anyone operating the ARRIFLEX 416 system should have these tools:; mm metric hex wrench; is used to attach baseplates.; Safety Specifications; with pure alcohol or a brand name lens cleaner.

ARRIFLEX 416 Quick Guide 05/2006, Page 3 About, Software, Tools, Safety About the 416 Preliminary Quick Guide This Quick Guide (order number K5.40076.0) provides a short introduction to the ARRIFLEX 416. This guide does not replace the ARRIFLEX 416 User’s Guide (K5.40077.0). It is essential that you...

Page 6 - Quick Specs; camera supply voltage.; Flange Focal Distance:

ARRIFLEX 416 Quick Guide 05/2006, Page 6 Quick Specs Fps range: 1 to 75 fps, forward only, in 0.001 fps increments Mirror Shutter: 180º to 45º, manually adjustableFixed settings at: 180º, 172.8º, 150º, 144º, 135º, 90º, 45ºUse the following angles for ﬁ lming with non-electronic ballast HMI or ﬂ uore...

Page 7 - Viewfi nder Indicators:; Power On button

ARRIFLEX 416 Quick Guide 05/2006, Page 7 1 . Total film exposed (or take counter) Standard speed. 2. Programmed speed. 3. Take counter (or total film exposed) Supply voltage & (with OBB-2), battery capacity/magazines left. 4. Timecode hours & minutes Timecode minutes & framerate 5. Timec...

Page 8 - Loading the 416 Magazine; Step 1: The Feed Side; Remove the film from the film can.; Transfer roller

ARRIFLEX 416 Quick Guide 05/2006, Page 8 Loading the 416 Magazine Note: The 416 magazine has its feed and take-up chambers on opposite sides to the SR 1, 2 & 3 magazines. Step 1: The Feed Side Load the unexposed film into the feed side in absolute darkness (darkroom or changing tent). • Open the...

Page 9 - Unlatch the footage counter roller arm.

ARRIFLEX 416 Quick Guide 05/2006, Page 9 Loading the 416 Magazine • Set the loop length by pulling the film head away from you and align it with the loop mark on the bottom of the magazine (see picture above). Adjust the loop length by turning the take-up film core. • Now take your hand off the film...

Page 10 - hand or the magazine before inserting the magazine.; Mounting the Magazine; Safety Catch

ARRIFLEX 416 Quick Guide 05/2006, Page 10 Mounting the Magazine • Insert the magazine throat into the magazine aperture in the back of the camera body and slide the magazine forward until it locks in place. Note: If the Shoulder Pad is attached to the camera, you will need to push down on the Should...

Page 11 - Changing Fps & Shutter Angle; While the desired speed is flashing, press SET to set the speed.; Checking the Mirror Shutter Angle; Before adjusting the mirror shutter, check that it is in the; Mirror Shutter centre

ARRIFLEX 416 Quick Guide 05/2006, Page 11 Changing Fps & Shutter Angle The NORM and PS/CCU buttons above the display select between preset Standard Speeds and user adjustable Programmable Speeds. Standard Speeds of 23.976, 24, 25, 29.97 & 30 fps are possible, while the Programmable Speed can...

Page 12 - Use the SET button to change the value of the flashing digit.; RGB ARRIGLOW; Set the display to mode 7.

ARRIFLEX 416 Quick Guide 05/2006, Page 12 Beeper, Backlight & RGB ARRIGLOW Beeper The 416 is equipped with a beeper which can sound when the camera is started or stopped. The upper line of display mode 6 allows the user to decide whether and when the beeper sounds and how loud (LS is shown for ‘...

Page 13 - Pull the battery backwards until the power connectors disengage.; release button

ARRIFLEX 416 Quick Guide 05/2006, Page 13 On-board Battery On-Board Batter y OBB-2 The OBB-2 On-Board Battery attaches directly to the camera body by means of a quick change mechanism that can be easily operated with one hand. The OBB-2 incorporates a built-in power meter to indicate the state of ch...

Page 14 - Integrated Video System; ON–OFF–CHECK/HIDE MENU switch; AUTO; Controlling image brightness

ARRIFLEX 416 Quick Guide 05/2006, Page 14 MINIMONITORconnectors Integrated Video System Video out with data or Y–signal Clean Video out (no data) or C–signal Video lens IRIS Focus adjustment Flicker free on/off button White balance button Manual Gain Control button ENTER/INSERT button ON–OFF–CHECK/ ...

Page 15 - VBS

ARRIFLEX 416 Quick Guide 05/2006, Page 15 Integrated Video System Automatic Gain Control • Press the MGC button to toggle between Manual Gain Control (LED on) and Automatic Gain Control (LED off). • When MGC is off, Automatic Gain Control will adjust the image brightness. Manual Gain Control • Press...

Page 16 - Accessories

ARRIFLEX 416 Quick Guide 05/2006, Page 16 Accessories

Page 18 - Turning Timecode Recording On and Off.; Press the MODE key until the display shows mode 4.; Userbit Input; The SET button changes the value of the flashing digit.; Magazine Timecode Sensitivity Switch; Timecode Operation; Display in mode 4. TC

ARRIFLEX 416 Quick Guide 05/2006, Page 18 Note: To write SMTPE timecode to film, ARRIFLEX 416 magazines must have the 416 Timecode Module fitted. Note: Timecode recording is only possible at the 5 Standard Speeds of 23.976, 24, 25, 29.97 & 30 fps. Turning Timecode Recording On and Off. • Press t...

Page 19 - Timecode Sensitivity Table; 6 mm Kodak Film Stocks

ARRIFLEX 416 Quick Guide 05/2006, Page 19 Timecode Sensitivity Table 16 mm Kodak Film Stocks Kodak 7201 (Color Negative) TCS 7 Kodak 7205 (Color Negative) TCS 6 Kodak 7212 (Color Negative) TCS 6 Kodak 7217 (Color Negative) TCS 6 Kodak 7218 (Color Negative) TCS 5 Kodak 7222 (B/W Negative) TCS 8 Kodak...

Page 20 - ARRI Group Addresses

ARRIFLEX 416 Quick Guide 05/2006, Page 20 ARRI Group Addresses Australia ARRI Australia PTY Limited (Sales, Ser vice & Rental) Unit 6C, 5 Talavera Road, Macquarie Park, Sydney. NSW 2113, AustraliaVoice phone: +61 (2) 9855 4300, FAX: +61 (2) 9855 4301Email: [email protected] Canada ARRI Canada Lim...

ARRI 416 - Manual

Table of Contents:

Summary

Other ARRI Models