Ariens C-2014R- Manual
Ariens C-2014R– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Remove Attachment Drive Belt; Loosen the hardware securing belt cover to unit.
- Page 3 – Replace Attachment Drive Belt; Tip housing and frame back together and secure with hex bolts.
- Page 4 – Replace chute crank and secure with spring clip pin.; If Equipped: Reconnect remote deflector cable to control lever.; Replace gear cover on top of chute pedestal.; RUN-IN ATTACHMENT BELT; Figure 2
- Page 5 – ATTACHMENT CLUTCH/BRAKE ADJUSTMENT; Remove Attachment Cable Slack; Safety
- Page 7 – ATTACHMENT DRIVE BELT PULLEY REPLACEMENT – POWER BRUSHES; Remove attachment pulley and discard. DO NOT reuse pulley.; Secure brush to frame with cap screws.
Page 1 of 8
Date: February 26, 2014 No. C-2014R
Replaces C-2014
Ariens Company has identified a potential safety concern on models and serials listed in the table below.
The auger drive pulley, #00268951, may develop a crack which could affect the brake's ability to stop the
auger/impeller, resulting in an unsafe condition.
Dealers are instructed to Stop Sale Immediately of any unsold inventory which falls into the model and
serial ranges listed. Additionally, dealers are asked to contact consumers who purchased affected
machines from your dealership to coordinate repair of those machines as soon as possible. Ariens
Company is sending a letter to registered owners of all affected machines alerting them to this situation.
Ariens Company has been reworking product since this issue was identified, and all machines which have
been reworked by Ariens Company will have a black check mark on the carton label as well as the model/
serial label on the machine.
Dealers are asked to order kit #52001800 and install it on each affected unit. The kit consists of a
replacement pulley and hub assembly. Dealers should file a warranty claim for each pulley replacement
using a flat rate code of 20999. Please make sure that the machine is within the model/serial numbers
listed below. Warranty claims will be reimbursed for 0.50 at the dealer's standard shop labor rate.
Please direct any questions to Ariens Technical Service at:
(888) 927 – 4367
Ariens Company
655 W. Ryan St.
Brillion, WI 54110
www.ariens.com
Service Campaign
Product Family:
Ariens Compact Sno-Thro, Ariens Compact Track Sno-Thro, Sno-Tek,
Ariens PB-28, Gravely PB- 28
Subject:
Important Product Safety Recall
Dealer Action:
STOP SALE – Repair Immediately
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Ariens C-2014R
Summary
Page 2 of 8 Date: February 26, 2014 No. C-2014R Replaces C-2014 ATTACHMENT DRIVE BELT PULLEY REPLACEMENT – SNO-THRO & SNO-TEK MODELS Models 920013, 920014, 920021, 920022, 920402, 920403, 939401 Remove Attachment Drive Belt (Figures 1, 2 and 3) 1. Shut off engine, remove key, disconnect spark pl...
Page 3 of 8 Date: February 26, 2014 No. C-2014R Replaces C-2014 IMPORTANT: To avoid bending bottom cover when tipping unit apart, support handlebars firmly or tip unit up on housing and remove bottom cover by removing six cap screws before separating unit. 9. Support Sno-Thro frame and housing. 10. ...
Page 4 of 8 Date: February 26, 2014 No. C-2014R Replaces C-2014 6. Replace chute crank and secure with spring clip pin. • If Equipped: Reconnect remote deflector cable to control lever. 7. Replace gear cover on top of chute pedestal. 8. Run in the attachment belt(see Run-in Attachment Belt on page 4...
