Page 3 - WARNING
3 5/30/02 Stated Sound Power Levels are established following Annex V “Internal Control of Production” of directive 2000/14/EC and assessment procedure EN-ISO 3744:1995. Les déclarations de niveau de puissance acoustique sont établies conformément à l'Article V « Contrôle interne de la production » ...
Page 4 - CONTROLS AND FEATURES
4 ENGLISH 1. Attachment Clutch Bail2. Chute Control Lever (932102)Chute Crank(932103, 310) 3. Muffler Guard4. Chute Deflector5. Discharge Chute6. Housing7. Throttle8. Spark Plug and Wire9. Oil Fill and Dipstick 10. Fuel Tank and Cap11. Primer Bulb12. Electric Starter (932103)13. Recoil Start14. Igni...
Page 5 - Figure 1
5 1 2 4 5 6 7 8 9 10 11 13 14 15 16 17 932102 OS2080OS1911 Figure 1 1 2 3 4 5 6 7 8 9 10 12 13 16 17 14 15 11 OS1746OS2071 932103932310 18 19 17 18 19 3
Page 6 - PRODUCT REGISTRATION; DISCLAIMER; TABLE OF CONTENTS
GB - 6 Controls and Features . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Maintenance . . . . . . . . . . . . . ....
Page 7 - Personal Safety Is Involved!; NOTATIONS; SAFETY
GB - 7 DELIVERY Customer Note: If you have purchased this product without complete assembly and instruction by your retailer, it is your responsibility to: 1. Read and understand all assembly instructions in this manual. If you do not understand or have difficulty following the instructions, contact...
Page 8 - High speed
GB - 8 SAFETY DECALS AND LOCATIONS ALWAYS replace missing or damaged Safety Decals. Refer to figure below for Safety Decal locations. 1. DANGER! 2. DANGER! SAFETY 3. HOT SURFACES! DANGER / PELIGRO ROTATING PARTS Stop engine & remove ignition keybefore clearing. PIECES EN ROTATION Arreter le mote...
Page 9 - Walk Around Inspection
GB - 9 ASSEMBLY SAFETY RULES Read, understand, and follow all safety practices in Owner/Operator Manual before assembling. Failure to follow instructions could result in personal injury and/or damage to unit.ALWAYS remove key and/or wire from spark plug before assembly. Unintentional engine start up...
Page 10 - Hazardous Slopes; FUEL SAFETY RULES
GB - 10 Rotating impeller can cause serious injury. DO NOT unclog unit while engine is running. When leaving operator’s position for any reason, ALWAYS disengage auger, stop unit and engine, remove key and allow moving parts to stop.Before starting engine, disengage control(s).Use only approved exte...
Page 11 - STORAGE SAFETY RULES; Tools Required; ASSEMBLY
GB - 11 MAINTENANCE AND SERVICE SAFETY RULES Before cleaning, removing clogs or making any inspections, repairs, etc.: disengage clutch(es), stop unit and engine, remove key, allow moving parts to stop. Allow hot parts to cool. Before tipping unit up onto housing, remove enough fuel so no spills wil...
Page 12 - Check Attachment Clutch Cable; top
GB - 12 Discharge Chute (932102) 1. Grease discharge chute ring if not already greased (Figure 4b). 2. Remove mounting hardware from top of engine. 3. Slide discharge chute over opening on housing and under the retaining clip. 4. Secure chute support bracket to studs on top of engine with mounting h...
Page 13 - without; OPERATION
GB - 13 3. Ensure Z bend end of clutch cable is connected to hole in tab on right side of clutch bail. Check Auger Gearcase Oil Check oil level in auger gearcase (see Maintenance Section). Fill Engine Crankcase IMPORTANT: Engines are shipped without oil in crankcase. Refer to Engine Manual for prope...
Page 14 - FILLING FUEL TANK; STARTING AND SHUT-OFF
GB - 14 Throttle The Throttle controls the engine speed. To increase or decrease the engine speed, adjust to:1.Fast (normal or warm starts)2.Part-Throttle3.Slow (cold weather starts)4."Stop" (engine is off) Recoil Starter Handle IMPORTANT: DO NOT let handle snap back against starter.When pul...
Page 15 - Emergency Stop; SNOW REMOVAL; Tips for Operation; TRAVELING
GB - 15 5. Insert key into ignition switch and push into RUN position. DO NOT twist key after inserting it. 6. Grasp starter handle and pull rope out slowly until it pulls harder. Let rope rewind slowly. 7. Pull rope with a rapid continuous full arm stroke. Let rope rewind slowly. NOTE: DO NOT allow...
Page 16 - MAINTENANCE; MAINTENANCE SCHEDULE
GB - 16 Secure unit chassis to transport vehicle. NEVER secure from rods or linkages that could be damaged.DO NOT transport machine while engine is running. SERVICE POSITION Place unit on a flat level surface. Before tipping unit up onto housing, remove enough fuel so no spills will occur. Tip unit ...
Page 17 - GENERAL LUBRICATION; Auger Shaft
GB - 17 To ensure adequate lubricant level: 1. Remove filler plug (Figure 5). Lubricant must be at least up to bottom of lubricant filler hole with unit resting on a level surface. 2. Add lubricant if required. Allow oil to drain to level of plug and replace plug. IMPORTANT: Use only Ariens special ...
Page 18 - SERVICE AND ADJUSTMENTS
GB - 18 ATTACHMENT DRIVE BELT REPLACEMENT Remove old attachment drive belt: 1. Shut off engine, remove key, disconnect spark plug wire and allow unit to cool completely. 2. Remove belt cover (Figure 4a, 4b). 3. If equipped with chute crank, remove spring clip from chute crank and remove chute crank....
Page 21 - AUGER EDGE REPLACEMENT; SCRAPER BLADE ADJUSTMENT; STORAGE; TROUBLESHOOTING; PROBLEM
GB - 21 AUGER EDGE REPLACEMENT Over time the rubber edges of the auger will wear. Contact your Ariens Dealer for replacement. IMPORTANT: Replace rubber edges before metal auger begins to wear. NOTE: After replacement of auger rubber edges, adjust scraper blade. See Scraper Blade Adjustment below. SC...
Page 22 - ACCESSORIES
GB - 22 To obtain a complete parts manual, find your model and serial number. Then go to www.ariens.com or call 1-800-678-5443. Engine stops. 1. Out of fuel.2. Mechanical jam in blower rake or impeller. 3. Polluted fuel supply.4. Faulty spark plug. 1. Fill fuel tank.2. Turn off engine, remove key, a...
Page 23 - SPECIFICATIONS
GB - 23 SPECIFICATIONS Model Number 932102 932103 932310 Description 520 624 624 Engine - Tecumseh HSSK50- 67409T OHSK60- 71505D OHSK60- 71504D Power Max - HP (Kw/min -1 ) 5 (3.73) 6 (4.47) Fast Idle Speed - RPM (min -1 ) 3600±150 Displacement - in (cc) 11.88 (195) Electric Start Optional 120V 120V ...
Page 24 - Year Limited Sno-Thro Warranty
GB - 24 3 Year Limited Sno-Thro Warranty Ariens Company warrants to the original purchaser that consumer products manufacturedby Ariens Company will be free from defects in material and workmanship for a periodof three (3) years after the date of purchase, and will repair any defect in material orwo...
