APC SU24R2XLBP - Manual - manualsarea.com

Page 3 - ANDLING

1 990-1048, Revision 1 12/00 1: S AFETY I NFORMATION American Power Conversion Corporation (APC) is the leading national and international manufac-turer of state-of-the-art uninterruptible power supplies, redundant switches, power management soft-ware, and related equipment. APC products protect har...

Page 4 - pluggable equipment; Operation Manual; Batteries must be recycled.

990-1048, Revision 1 12/00 2 n Use one hand, whenever possible, to connect or disconnect signal cables to avoid a possible shock from touching two surfaces with different electrical grounds. n Connect the equipment to a three wire AC outlet (two poles plus ground). The receptacle must be connected t...

Page 5 - NSTALLATION; NPACKING; UPS; The UPS is heavy. Select a location sturdy enough to han-; NSTALLING THE; Install the UPS at or near the bottom of the rack.

3 990-1048, Revision 1 12/00 2: I NSTALLATION The UPS has a “rack and stack” design that provides two mounting options. The UPS can be mounted in a 19-inch equipment rack or stacked on a battery pack(s) model SU24RMXLBP2U. Hardware is provided for either option. U NPACKING 1. Inspect the UPS upon re...

Page 6 - Turn the UPS right side up and place it either on the floor on

990-1048, Revision 1 12/00 4 S TACKING THE UPS ON A B ATTERY P ACK Note: For rack mounting, proceed to Mounting the UPS in a Rack , below. 1. Unpack the four mounting feet shipped in the mounting kit. 2. Turn the UPS on its side so the bottom surface is accessible. 3. Locate the indentations on the ...

Page 8 - Reinstalling the Battery; ONNECTING THE

990-1048, Revision 1 12/00 6 4. Use the handles on the side of the UPS to sup- port the unit. Due to the weight of the UPS, two people are re-quired to install it in the rack. 5. In four-post mounting each side of the UPS has a cleat that must slide into the groove on the rails. Slide the UPS in...

Page 10 - URNING ON THE

990-1048, Revision 1 12/00 8 C ONNECTING P OWER AND E QUIPMENT TO THE UPS 1. Plug the UPS into a two-pole, three-wire, grounding receptacle only. Avoid using extension cords and adapter plugs. Your UPS is not supplied with an input line cord. Three output line cords are supplied for connecting equip...

Page 11 - requires; that batteries are disconnected; ISCONNECTING THE

9 990-1048, Revision 1 12/00 3: T RANSPORTING Y OUR S MART -UPS The UPS may be transported in or out of the rack. In either case the battery must be disconnected! Always DISCONNECT THE BATTERY before shipping the UPS to avoid damage during transport. (U.S. Federal Regulation requires that batteries ...

Page 12 - EMOVING THE; FROM THE

990-1048, Revision 1 12/00 10 R EMOVING THE UPS FROM THE R ACK If your UPS is mounted in a rack and you are removing it from the rack for transport: n Remove the four ornamental screws that secure the unit to the rack. n Grasp the handle located on the front of the UPS and pull the unit halfway out ...

Page 13 - ROUBLESHOOTING; ROBLEM AND

11 990-1048, Revision 1 12/00 4: T ROUBLESHOOTING Use the chart below to solve minor UPS installation problems. Contact APC for assistance with complex UPS problems. Refer to the Operation Manual for operational problems. P ROBLEM AND P OSSIBLE C AUSE S OLUTION UPS WILL NOT TURN ON ON button not pus...

Page 15 - ONTACTING; APC; Refer to the information provided at the APC Internet site:

13 990-1048, Revision 1 12/00 5: C ONTACT , R EGULATORY , AND W ARRANTY I NFORMATION C ONTACTING APC Refer to the information provided at the APC Internet site: http://www.apcc.com/support/contact If you ordered a Smart-UPS SU1400R3XLIX171 unit, refer to the red addendum sheet (part number 990-1023A...

APC SU24R2XLBP - Manual

Table of Contents:

Summary

Other APC Models