APC RT 1000/2000 - Manual - manualsarea.com

Page 3 - ANDLING

1 990-1060B 12/2005 1: S AFETY I NFORMATION American Power Conversion Corporation (APC) is the leading national and international manufac-turer of state-of-the-art uninterruptible power supplies, redundant switches, power management soft-ware, and related equipment. APC products protect hardware, so...

Page 4 - pluggable equipment

990-1060B 12/2005 2 • In order to maintain compliance with the EMC directive, output cords attached to the UPS should not exceed 10 meters in length. D EENERGIZING S AFETY • If the equipment has an internal energy source (battery), the output may be energized when the unit is not connected to an AC ...

Page 5 - NSTALLATION; NPACKING; UPS; Place the UPS where it will be used.; Select a location sturdy enough to handle the; Placement; Sm

3 990-1060B 12/2005 2: I NSTALLATION U NPACKING Inspect the UPS upon receipt. APC designed robust packaging for your product. However, accidents and damage may occur during shipment. Notify the carrier and dealer if there is damage. The packaging is recyclable; save it for reuse or dispose of it pro...

Page 8 - URN ON THE; CCESSORIES

990-1060B 12/2005 6 6. T URN ON THE UPS Make sure the battery is connected before turning on the UPS! Press the button on the front panel to power up your UPS. This will power up connected equipment if that equipment is turned on. The UPS charges its battery when it is connected to utility power. Th...

Page 9 - PERATION; NDICATORS AND; For Position Only; The ON

7 990-1060B 12/2005 3: O PERATION I NDICATORS AND C ONTROLS The UPS power control and operating indicators are located on the front display panel. The input and output connectors are on the rear panel. F RONT P ANEL For Position Only | The ON and OFF buttons power the UPS and act as master controls ...

Page 10 - User Configurable Items

990-1060B 12/2005 8 O PERATION Power On Press and release the button to supply power to the UPS and connected equipment. Cold Start When the UPS is off and there is no utility power, use the cold start feature to apply power to the connected equipment from the UPS’s battery. Cold start is not a norm...

Page 11 - Online; The online; Utility; Press and hold the; Bypass

9 990-1060B 12/2005 U TILITY P OWER During normal operation, the UPS monitors the utility power and delivers power to the connected equipment. If your system is experiencing excessive periods of high or low voltage, have a certified electrician check your facility for electrical problems. If the pro...

Page 12 - On Battery; HUTDOWN

990-1060B 12/2005 10 B ATTERY P OWER If the utility power fails, the UPS can provide power to the connected equipment from its internal batteries for a finite period. The UPS sounds an alarm—four beeps every 30 seconds—while operat-ing on battery. The alarm stops when the UPS returns to online opera...

Page 13 - ASIC; If used, connect the

11 990-1060B 12/2005 R EAR P ANEL TVSS Ground Input Plug Computer Interface Port Fan External Battery Connector Port Outlets B ASIC C ONNECTORS Computer Inter- face Port Power management software and interface kits can be used with the UPS. Use only interface kits supplied or approved by APC. If use...

Page 14 - UPS ID

990-1060B 12/2005 12 O N B ATTERY O PERATION The UPS switches to battery operation automatically and an internal alarm sounds (periodic beeps) if the utility power fails. Press the ON button (front panel) to silence the UPS alarm until low battery (for the current outage only). You can change the au...

Page 16 - RANSPORTING YOUR; Rack Mount Installation Sheet; TORAGE

990-1060B 12/2005 14 4: T RANSPORT , M AINTENANCE , AND T ROUBLESHOOTING T RANSPORTING YOUR UPS Always DISCONNECT THE BATTERY before shipping in compliance with U.S. Department of Transportation (DOT) regulations. The battery may remain in the UPS; it does not have to be removed. This requirement ap...

Page 17 - EMOVE AND; Installation

15 990-1060B 12/2005 R EPLACING THE B ATTERY P ACK This UPS has an easy to replace, hot-swappable battery pack. Replacement is a safe procedure, iso-lated from electrical hazards. You may leave the UPS and connected equipment on while replacing the battery. See your dealer or contact APC for informa...

Page 18 - Replace Battery

990-1060B 12/2005 16 T ROUBLESHOOTING Use the chart below to solve minor UPS installation problems. Refer to the APC web site www.apc.com for assistance with complex UPS problems. P ROBLEM AND P OSSIBLE C AUSE S OLUTION UPS WILL NOT TURN ON ON button not pushed. Press the ON button once to power the...

Page 19 - ETURN THE UNIT BY INSURED

17 990-1060B 12/2005 S ERVICE 1. Review the problems discussed in the Troubleshooting section of this manual to eliminate com- mon problems. 2. Verify that no circuit breakers are tripped. A tripped circuit breaker is the most common prob-lem. 3. If the problem persists, call APC Customer Service or...

Page 20 - Refer to the information provided at the APC Internet site:

990-1060B 12/2005 18 5: C ONTACT , R EGULATORY , AND W ARRANTY I NFORMATION C ONTACTING APC Refer to the information provided at the APC Internet site: http://www.apc.com/support R EGULATORY A GENCY A PPROVALS N 394 B ME 61 D ECLARATION OF C ONFORMITY

APC RT 1000/2000 - Manual

Table of Contents:

Summary

Other APC Models