APC PMF4S-A - Manual
APC PMF4S-A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – DANGER; HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH; CAUTION; LOSS OF BRANCH CIRCUIT POWER AND SURGE PROTECTION; WARNINGS; APC MODULAR PANEL PRODUCTS Surge Protective Device (SPD)
- Page 3 – LOSS OF SURGE PROTECTION
- Page 4 – TABLE OF CONTENTS
- Page 5 – INTRODUCTION; Thank you for choosing the APC; Check all applicable electrical codes to assure compliance.; . The electrician should follow the steps detailed in; A copy of the installer’s invoice, detailing the installation of
- Page 6 – Read the entire; PACKAGING
- Page 7 – IDENTIFICATION
- Page 8 – connections to the following values.; Ground; ELECTRICAL
- Page 9 – Figure 2: Wiring Practice; WARNING; LOCATION OF SPD; SPD
- Page 10 – SYSTEM GROUNDING; INADEQUATE RACEWAY ELECTRICAL CONTINUITY
- Page 11 – INSTALLATION; voltages on the protected equipment. For every foot of wire length,
- Page 12 – Follow steps 1–5 to make wiring connections.; NOTE: Always install the SPD on the LOAD side of the main disconnect.; WIRING; together and kept as short as possible (do not loop or coil wires) to
- Page 13 – WIRING DIAGRAMS WITHOUT INTEGRAL DISCONNECT; neutral and ground lugs together.
- Page 14 – WIRING DIAGRAMS WITH INTEGRAL DISCONNECT
- Page 15 – The SPD display panel shows the status of the modules with; Figure 7: SPD Module LEDs (Wye and Split Phase configurations); diagnostically; OPERATION
- Page 16 – Note: Three phase model shown
- Page 17 – Table 3: Dry Contact Configuration; NC; DRY CONTACTS
- Page 18 – MAINTENANCE AND
- Page 19 – of the diagnostic display panel.
- Page 20 – informational purposes only.; CUSTOMER SUPPORT; APC Worldwide Customer Support; Global support searching APC Knowledge Base and using e-support.; APC; Customer Support Center by telephone or e-mail.
APC Modular Panel Products
The APC Modular Panel Product Surge Protective Devices (SPD)
are designed to provide protection at the service entrance, branch
panels or other critical locations for today’s electrical equipment.
Compliant with UL 1449 2nd Edition requirements
dated February 9, 2007.
PMF3S-A
PMF3DS-A
PMP3S-A
PMP3DS-A
PMG3S-A
PMG3DS-A
PML3S-A
PML3DS-A
PMF4S-A
PMF4DS-A
PMP4S-A
PMP4DS-A
PMG4S-A
PMG4DS-A
PML4S-A
PML4DS-A
PMH4DSLM-A
Installation and Operation Manual
Surge Protective Devices (SPD)
1-800-800-4272 | www.apc.com
Retain for future use
The APC SurgeArrest® Modular Panel Mount Products have
replaceable phase modules with integrated LED monitoring, a
display panel with surge counter and LED status indicators, an
audible alarm, and a NEMA 3R/12 Enclosure. Modular Panel
Products are available with 120kA and 160kA maximum surge
current per phase ratings.
PML-4Y-DC-DL-A
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH · Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E.· This equipment must only be installed and serviced by qualified electrical personnel.· Turn off all power supplying this equipmen...
CAUTION LOSS OF SURGE PROTECTION · During installation into an electrical system, SPD’s must not be energized until the electrical system is completely installed, inspected, and tested. All conductors must be connected and functional, including the neutral. The voltage rating of the device and syste...
CONTENTS INTRODUCTION .............................................................................. UNPACKING AND PRELIMINARY INSPECTION ............................... STORAGE ........................................................................................ IDENTIFICATION NAMEPLATE ...........
