APC 7500/10000 VA - Manual - manualsarea.com

Page 3 - Introduction; NSTALLATION; Unpacking; Ensure the air vents on the front and rear of the UPS are not blocked.

1 Introduction The APC Smart-UPS RT is a high-performance, uninterruptible power system (UPS), designed to prevent blackouts, brownouts, sags and surges from reaching your computers, servers, and other sensitive electronic equipment. 1: I NSTALLATION Attention: Read the safety information sheet befo...

Page 4 - Hardwiring; Attention: Wiring must be performed by a qualified electrician.; Switch the UPS input circuit breaker (see; Adhere to all; XLTW M; XLI M

2 Hardwiring Attention: Wiring must be performed by a qualified electrician. 1. Install a utility circuit breaker in accordance with local electrical codes (see tables below) for input wiring only. 2. Switch the UPS input circuit breaker (see A ) and utility circuit breakers OFF. 3. Remove the acces...

Page 8 - Serial Port; EPO Option; TVSS Screw; for the information on

6 B ASIC C ONNECTORS Serial Port Power management software and interface kits can be used with the UPS. Use only interface kits supplied or approved by APC. Ethernet Port Connect the UPS to the network. (Located on Web/SNMP card.) EPO Terminal The optional Emergency Power Off (EPO) feature allows co...

Page 9 - PERATION; Indicator Description; Troubleshooting; Feature Function; Press this button to turn off the UPS.

7 2: O PERATION F RONT D ISPLAY P ANEL Indicator Description Online The UPS is drawing utility power and performing double conversion to supply power to connected equipment (see Troubleshooting ). On Battery The UPS is supplying battery power to the connected equipment. Bypass The UPS is in bypass m...

Page 10 - On Battery Operation

8 Feature Function Normal /Bypass Manually switch connected equipment to bypass mode, so that utility power is sent directly to connected equipment. Battery operation is not available while the UPS is in bypass mode. (See Troubleshooting. ) Cold Start This is not a normal condition. Supply immediate...

Page 13 - Adhere to national and local electrical codes when wiring.; CL2: Class 2 cable for general use

11 EPO (Emergency Power Off) Option The output power can be disabled in an emergency by closing a switch connected to the EPO. Adhere to national and local electrical codes when wiring. The switch should be connected in a normally open switch contact. External voltage is not required; the switch is ...

Page 14 - Terminal Mode to Configure UPS Parameters; Network Shutdown

12 Terminal Mode to Configure UPS Parameters Terminal Mode is a menu driven interface that enables enhanced configuration of the UPS. Connect the serial cable to the serial port on the back of the UPS. When using PowerChute ® Network Shutdown software: 1. Open a terminal program. Example: HyperTermi...

Page 15 - Storage; Use caution when handling heavy battery modules.; Transporting the UPS

13 4: S TORAGE , M AINTENANCE , AND T RANSPORTING Storage Store the UPS covered and positioned as for proper functioning, in a cool, dry location, with the batteries fully charged. (Batteries must be charged every six months.) Store at: 0-50,000 ft (0 - 15,000 m) 5 ° -113 ° F ( -15 - 45 ° C) Replaci...

Page 16 - ROUBLESHOOTING; , for assistance with complex UPS problems.

14 5: T ROUBLESHOOTING Use the table below to solve minor installation and operation problems. Refer to the APC web site, www.apc.com , for assistance with complex UPS problems. P ROBLEM AND P OSSIBLE C AUSE S OLUTION UPS WILL NOT TURN ON Batteries are not connected properly. Check that the battery ...

Page 18 - Service; Contacting APC; Support

16 Service If the UPS requires service do not return it to the dealer. Instead, follow these steps: 1. Review the problems discussed in the Troubleshooting section of this manual to eliminate common problems. 2. If the problem persists, contact APC Customer Service through the APC web site, www.apc....

Page 19 - Regulatory Agency Approvals and Radio Frequency Warnings; BSMI

17 6: R EGULATORY AND W ARRANTY I NFORMATION Regulatory Agency Approvals and Radio Frequency Warnings 200, 208, 220, 230, 240 V MODELS This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take corrective actions. Th...

Page 20 - Declaration of Conformity

Page 21 - Limited Warranty

19 Limited Warranty American Power Conversion (APC) warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective prod...

APC 7500/10000 VA - Manual

Table of Contents:

Summary

Other APC Models