A.O. Smith AOSTT35300 - Manual
A.O. Smith AOSTT35300 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Commercial Storage Tanks
- Page 3 – DIMENSION AND SHIPPING WEIGHTS; HORIZONTAL TANK SADDLES
- Page 4 – UNINSULATED; STANDARD STOCK BARE STORAGE TANKS
Commercial Storage Tanks
UNINSULATED
STANDARD STOCK BARE STORAGE TANKS
Page 1 of 4
June 2008R
AOSTT35300
A. O. Smith commercial hot water storage tanks are designed for use with gas/electric water
heaters and boilers to provide additional hot water storage capacity for systems with large hot
water draws. A. O. Smith glass-lined storage tanks are designed and recommended for systems
with operating temperatures up to 180°.
PERMAGLAS
®
GLASS LINING
n
All internal surfaces exposed to water are glass-lined per ASME HLW procedures,
using an NSF-approved glass-lining compound
n
Glass is highly resistant to effects of temperature, corrosion and electrolysis
SIZES FROM 80 TO 1,000 GALLONS IN STOCK
n
All tanks in table on reverse side are normally carried in stock for immediate
shipment, providing a fast solution for retrofit requirements
HORIZONTAL OR VERTICAL MOUNTING
n
A. O. Smith standard stock tanks (except the T-80S, T-120S and TL-500A) are
shipped factory standard with leg sockets for vertical installation,
but are also
designed to have the proper inlet/outlet openings
that allow horizontal installation
n
For horizontal installations, optional tank saddles are
required (TL-500A is horizontal only)
T-325 ASME RETROFIT SPECIAL
n
The T-325 ASME (34 x 84) is designed to provide maximum storage
capacity and fit through a 36” door
MAGNESIUM ANODES
n
For extra protection against corrosion
WORKING PRESSURES
n
Tanks tested at pressures assigned in accordance with working pressures shown in table
on reverse side
CUSTOM TANKS
n
In order to offer storage tanks for immediate shipping, the A. O. Smith Standard
Stock Tanks are offered with only those openings and features shown in the
following tables
n
A. O. Smith also offers a full line of custom tanks from 80 to 12,500 gallons built to meet
your specifications and are available with many options such as various working
pressures, lifting lugs, handholes, manholes, special linings, special openings, factory
jacket/installation, and built to military specifications
n
For custom tanks, please see the A. O. Smith Custom-Line HD storage
tank spec sheet
(OPTIONAL)
MODELS
T-80
THROUGH
T-1000
CRN
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
OPTIONS n ASME and National Board Certification sheets - furnished upon request n Tanks saddles - two per horizontal tank required FIVE-YEAR LIMITED TANK WARRANTY n For complete information, consult written warranty or contact A. O. Smith FIGURE 1 -T-80, T-120 NOTE:T-120 ShOwN. FIGURE 2 - T-140 THRU...
Page 3 of 4 www.hotwater.com AOSTT35300 Commercial Storage Tanks DIMENSION AND SHIPPING WEIGHTS Working pressure for Std. models T-80, T-120 and T-200: 150 psiWorking pressure for ASME models T-140 and T-200 through T-1000: 125 psi OPTIONAL TANK SADDLES FOR HORIZONTAL TANK INSTALLATIONS HORIZONTAL T...
SUGGESTED SPECIFICATION Glass-lined storage tank(s) shall be A. O. SMITH glass-lined storage tank(s) or equal. Tank(s) shall be _” x _” and have a nominal capacity of _ gallons. Tank(s) shall have threaded openings as shown on drawings. Exterior of tank(s) shall be thoroughly cleaned and painted. In...
