Page 3 - Table of Contents; Section 1: Introduction; Section 4: Cooling System
3 Table of Contents Section 1: Introduction 1.1 Getting to Know Your Chassis ............................................................................ 5 1.2 Chassis Specifications......................................................................................... 6 1.3 Included Screws .........
Page 4 - Section 1; Introduction; User Manual
4 Section 1 Introduction One / One S / One S3 User Manual
Page 5 - Getting to Know Your Chassis
5 1.1 Getting to Know Your Chassis 1. 3 x 5.25” drive bays 2. 5 x 3.5” drive bays 3. 2 x 2.5” drive bays 4. 1 x 120 mm top exhaust fan (standard) 5. 1 x 120 mm rear exhaust fan (standard) 6. 1 x 120 mm side intake fan (optional) 7. 1 x 120 mm front intake fan (optional) 8. 1 x 120/140 mm bottom inta...
Page 6 - Chassis Specifications
6 1.2 Chassis Specifications Chassis Type Mid Tower Chassis Color Black Dimensions 17.2” (H) x 8.2” (W) x 19.2” (D) 438 mm (H) x 208 mm (W) x 488 mm (D) Weight One: 10.8 lbs / 4.9 kg One S / One S3: 10.4 lbs / 4.7 kg Cooling One: - 1 x 120 mm top exhaust fan - 1 x 120 mm rear exhaust fan - 1 x 120 m...
Page 7 - Included Screws
7 1.3 Included Screws An inventory of all screws and intended usage and quantity is provided here: A. PSU screws (10) B. Motherboard standoffs (3:4 preinstalled) C. Motherboard screw (9) D. 5.25”/2.5” optional drive screw (10) E. Front panel fan screws (2) F. Drive bay rails for 3.5” (5 pairs) G. Zi...
Page 8 - Section 2; Hardware Installation
8 Section 2 Hardware Installation One / One S / One S3 User Manual
Page 9 - Setting Up; Removing the Side Panels and Front Bezel
9 2.1 Setting Up When working in your case, please keep the following in mind: Put the case upright on a flat, stable surface so that the rear panel (power supply and expansion slots) is facing you. Handle all components and cards with care. To avoid electrostatic discharge, ground yourself pe...
Page 10 - Motherboard Installation
10 2.3 Motherboard Installation Before proceeding, check the manual for your CPU cooler to find out if there are steps you must do before installing the motherboard. Make sure you have the correct I/O panel for your motherboard. If the panel provided with the chassis isn’t suitable, please contact y...
Page 11 - Power Supply Installation
11 2.4 Installing KUHLER H 2 O Liquid Coolers The following instructs how to install the Antec KUHLER H 2 O liquid CPU cooler (620 / 920). For any other CPU coolers, please consult your manufacturer’s installation guide. Caution : Check your motherboard’s CPU socket to ensure its compatibility with ...
Page 12 - External 5.25” Device Installation
12 Press down on the drive cover tabs. 2.6 External 5.25” Device Installation The One / One S / One S3 can support up to three 5.25” devices. 1. Remove the side panels and front bezel as directed in Section 2.2. 2. Remove the drive bay cover by pressing out on the two small tabs on either side of th...
Page 13 - Internal 2.5” Device Installation
13 2.7 Internal 2.5” Device Installation There are two 2.5” drive mounting locations in the One / One S / One S3: at the base of the drive cage and a dedicated mount in the middle of the drive cage. To install at the base of the drive cage: 1. Remove the side panels as described in Section 2.2. 2. S...
Page 14 - Internal 3.5” Device Installation; Cable Management
14 2.8 Internal 3.5” Device Installation The One / One S / One S3 includes 5 pairs of 3.5” drive rails. You will need 1 pair per 3.5” drive. 1. Line up the drive rail pins to the sides of your 3.5” drive. Ensure that the squeeze-tabs are aligned on the side of your drive that does not have power or ...
Page 15 - Section 3
15 Section 3 Front I/O Ports One / One S / One S3 User Manual
Page 16 - USB Ports; AC’97 / HD Audio Ports
16 Pin Signal Names (HDA) Pin Signal Names (AC’97) 1 MIC2L 1 MIC In 2 AGND 2 GND 3 MIC2R 3 MIC Power 4 AVCC 4 NC 5 FRO-R 5 Line Out(R) 6 MIC2_JD 6 Line Out(R) 7 F_IO_SEN 7 NC 8 Key (no pin) 8 Key (no pin) 9 FRO-L 9 Line Out(L) 10 LINE2_JD 10 Line Out(L) Pin Signal Names Pin Signal Names 1 USB Power ...
Page 17 - Power Switch / Reset Switch / Hard Disk Drive LED Connectors
17 3.3 Power Switch / Reset Switch / Hard Disk Drive LED Connectors Connected to your front panel are LED leads for power and HDD activity, as well as switch leads for the power and reset buttons. Attach these to the corresponding connectors on your motherboard. Consult your motherboard manual for s...
Page 18 - Rewiring Motherboard Header Connections
18 3.4 Rewiring Motherboard Header Connections There may come a time when you need to reconfigure the pin-out of a motherboard header connector. Examples could be for your USB header, audio input header, or some other front panel connector such as the Power Button connector. Before performing any wo...
Page 19 - Section 4; Cooling System
19 Section 4 Cooling System One / One S / One S3 User Manual
Page 20 - Included Fans
20 4.1 Included Fans One : The One comes with two standard fans (yellow outline) – a rear 120 mm exhaust fan and a top 120 mm exhaust fan. The red rectangles indicate additional fan mounts. Mounting procedures for these fans is discussed in Section 4.2. One S / One S3 : The One S and One S3 come wit...
Page 21 - Optional Fans; Front intake 120 mm fan
21 4.2 Optional Fans One: The One includes mounts for up to three more fans. These mounts are as follows: - 1 x front intake 120 mm mount - 1 x side 120 mm mount - 1 x bottom 120/140 mm mount One S / One S3: The One S / One S3 includes mounts for up to four more fans. These mounts are as follows: - ...
Page 22 - Rear 120 mm fan – One S / One S3 only; PSU Air Filter
22 Bottom 120/140 mm fan At the base of the case, there is a fan mount that can fit either a 120 mm or 140 mm fan for additional air intake. 1. Remove the left side panel as outlined in Section 2.2. Rest the case on its side so you have access to both sides of the fan mount. 2. Align your fan with t...
