American Standard 7507.103 - Manual
American Standard 7507.103 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – LOCKING TAB
- Page 3 – Tightening Sequence For Clips
- Page 4 – M a i n t e n a n c e f o r s t a i n l e s s s t e e l s i n k s :; risk that rust stains will attack the steel.
- Page 5 – S T A I N L E S S S T E E L S I N K S; CAUTION; S I N K C U T O U T S :
- Page 6 – S U P P O R T C L I P L O C A T I O N S :
- Page 7 – END
C U L I N A I R E C O L L E C T I O N ™
S T A I N L E S S S T E E L
K I T C H E N S I N K S
M O D E L S 7 5 0 1 . 1 0 3 , 7 5 0 2 . 1 0 3 , 7 5 0 2 . 4 0 3 ,
7 5 0 4 . 1 0 3 , 7 5 0 7 . 1 0 3 , 7 5 1 0 . 1 0 3
7 9 0 7 6 7 - 1 0 0
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
B E F O R E Y O U B E G I N . . .
38
(965mm)
CULINAIRE DUAL LEVEL SINK
WITH DRAIN BOARD
MODEL 7510
32-1/8
(816mm)
CULINAIRE DOUBLE BOWL SINK
MODEL 7502
17
(432mm)
CULINAIRE ISLAND SINK
MODEL 7507
SELF RIMMING
24-1/4
(616mm)
21-1/8
(537mm)
CULINAIRE SINGLE BOWL SINK
MODEL 7501
32
(813mm)
CULINAIRE DUAL LEVEL
BOWL SINK
MODEL 7504
Certified to comply with ANSI A112.19.3M
CAN/C.S.A. B-45
Observe local plumbing and building codes.
I M P O R T A N T : D I M E N S I O N O F F I X T U R E S A R E N O M I N A L A N D M A Y V A R Y W I T H I N
T H E R A N G E O F T O L E R A N C E S E S T A B L I S H E D B Y A . N . S . I . A N D C . S . A . S T A N D A R D S .
© A M E R I C A N S T A N D A R D I N C . 2 0 0 2
™
Unpack new sink and inspect carefully for
damage. Replace the sink in its original packing
carton to protect it until you are ready to begin
installation.
CUTOUT DIMENSIONS FOR SINKS:
Recommended Tools & Materials
Countertop Cutout Dimensions
Putty Knife
Pipe Wrench
Channel Locks
Long Phillips Screwdriver
or Regular Screwdriver
Adjustable Wrench
Drill
Below are the dimensions needed to determine the cutout size
for each sink. Select the correct diagram for your sink and refer
to the instructions below.
Locate and mark center lines of sink on countertop.
Provide proper clearance under the countertop for the faucet
supply lines and the structural parts of the cabinet.
By using the diagrams below and measuring your sink, draw the
outline of the sink cutout onto the countertop. This is the cutting
outline.
Remember that the size of the sink is larger than the cutout.
Basin Wrench
Saber Saw
Plumber's Putty or Caulk
Tubing Cutter
Tape Measure
Hacksaw
Mineral Spirits
Silicone Sealant
21-1/8
(537mm)
21
(533mm)
21
(533mm)
21
(533mm)
1
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Perimeterof sink Cutout 1 Drill a clearance hole inside the cutout lineas marked on thecountertop. AFTER THE CUTOUT IS DRAWN... © A M E R I C A N S T A N D A R D I N C . 2 0 0 2 Perimeterof sink Cutout 2 A B Single Bowl Double Bowl Trap Trap 3 5 4 6 8 9 7 Connect supply linesto faucet finger tight,a...
MODEL 7502 & 7504 MODEL 7507 MODEL 7510 MODEL 7501 11 3 1 9 11 6 2 4 13 12 3 1 5 14 11 5 1 3 4 2 1 3 13 12 4 2 6 14 12 2 4 10 5 6 9 10 7 8 7 8 9 10 6 8 7 5 7 8 Tightening Sequence For Clips © A M E R I C A N S T A N D A R D I N C . 2 0 0 2 7 9 0 7 6 7 - 1 0 0 3
© A M E R I C A N S T A N D A R D I N C . 2 0 0 2 Product names listed herein are trademarks of American Standard Inc.unless otherwise noted. M a i n t e n a n c e f o r s t a i n l e s s s t e e l s i n k s : P l e a s e h a v e t h e f o l l o w i n g i n m i n d : D i s c o l o r a t i o n 7 9 0 ...
