Amana ARTC7021W-P1143814NW - Installation Manual
Amana ARTC7021W-P1143814NW – Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – -wire Cord Installed
- Page 3 – See
- Page 4 – WARNING; • ALL RANGES CAN TIP; Minimum Clearances to Combustible Surfaces; OR
- Page 5 – Before You Install; Installation Requirements; C o n s id e r
- Page 6 – Range and Cabinet Dimensions; Electrical Receptacle Location
Installation
Instructions
Electric Range
Keep instructions for future reference. Be sure manual stays with range.
Read entire instruction before beginning installation.
Read Owners Manual for safe installation.
PREPARE TO
INSTALL RANGE
AND INSTALL
ANTI-TIP
BRACKET
Measure cabinet area and prepare
it according to illustrations in
Minimum Clearances to
Combustible Surfaces and Range
and Cabinet Dimensions section in
this manual.
Remove the packing
materials and locate
the anti-tip bracket,
screws and plastic
anchors.
1
3
1
/
2
"
Anti-tip
bracket can
be installed
on either
side of
range.
Anti-tip Bracket Installation
To avoid risk of range tipping, secure
range with a properly installed anti-
tip bracket.
1.
Measure and mark 3
1
/
2
" from
back wall on either right or left
side of cabinet cutout.
2.
Place anti-tip bracket 3
1
/
2
" from
back wall and against the side
cabinet.
• If range is not installed
beside cabinet(s), position
range where it will be
installed. Draw a line along
side of range. Remove range
and place anti-tip bracket
with back edge 3
1
/
2
“ from
back wall and on the line
drawn along side of range.
3.
Mark 2 hole locations in anti-tip
bracket, remove bracket and
drill 2 holes.
• If drilling into wood, use a
3
/
32
" drill bit.
• If drilling into concrete, use a
3
/
16
" masonry drill bit and
insert plastic anchors.
4.
Secure bracket to floor using
screws supplied.
5.
After range is in final position,
remove range storage drawer
or lower panel and confirm anti-
tip bracket is engaged with
range leveling leg.
You'll Need a Few
Things Before You Begin
Important–
Save for local electrical inspector’s use.
Wrench
Screw
Drivers
Level
Power Cord
(3-wire or 4-wire)
and Strain Relief
Tape Measure
Drill and DrillBit
3
/
32
" for wood floor
3
/
16
" for concrete floor
3
/
8
" Nut Driver
or Sockets
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Amana ARTC7021W-P1143814NW
Summary
CONNECT ELECTRICAL CORD To place electrical receptacle, seeElectrical Receptacle Locationdiagram in this manual. 2 3-wire or 4-wire Plug Connection Four-wire cord is required for mobile homes or where codes (Canada) do notpermit grounding through neutral. 1. Remove access cover from rear of range. 2...
POSITION AND LEVEL RANGE Place range near final position andplug in. Then, slide range into finalposition and adjust all legs (4) untilrange is level side to side and frontto back. • Place a level on top oven rack or on range top when leveling. • Leveling legs must extend ¼ inch to engage anti-tip b...
IMPORTANT SAFETY INFORMATION SAVE THESE INSTRUCTIONS WARNING ! To reduce risk of the appliance tipping, it must be secured by aproperly installed anti-tip bracket(s). To make sure bracket has beeninstalled properly, remove the storage drawer or panel and lookunder the range with a flashlight. Bracke...
