Amana AM33LP-P- User Manual

1. Using a utility knife, cut the tape to open top flaps of carton. 2. Remove Assembly/Installation Instructions and Use and Care Guide. 3. Remove the large cardboard panels on the top and each side of the inside of the carton. 4. Remove the cart base on the top of the inside of the carton. 5. Remov...

ASSEMBLED GRILL VIEW A C D E F G H J I K A. Control knob: main burnersB. Control knob: back IR burnerC. Side shelfD. Grilling/cooking surfaceE. Bread warming rackF. Roll top grill hoodG. Hood handleH. Side burner with griddle I. Electronic igniter: main burners, back IR burner and side burner J. Con...

ASSEMBLY INSTRUCTIONS Step 1: Assemble Wheel Channels 1. Remove the four (4) caster assembly nuts and two (2) bolts from the wheel channel assemblies. Note: The nuts and bolts are hand tightened to the wheel channels. 2. Set the cart base on the floor and then lay the wheel channel left on the left ...

Step 2: Assemble Grill Cart 1. Place the cart side left onto the two (2) outer caster assembly bolts, make sure the large flange is toward the front of the cart base. 2. Secure the cart side left in place by tightening the caster assembly nuts onto the caster assembly bolts. 3. Use six (6) self-tapp...

1. Take the side burner package out from inside the grill head. 2. Tilt the grill head on its back and loosen the four (4) grill mounting bolts so that there is approxi- mately 1/4” between the bolt head and grill bottom. Note: The bolts are already attached to the grill head bottom. 3. Unpack the s...

ASSEMBLY INSTRUCTIONS Step 4: Assemble Drawers A. Handle B. Drawer front face C. Phillips head screws D. Drawer tray E. Self-tapping screws 14 A B C E D 1. With a Phillips head screwdriver, remove the two phillips pan head screws from the handle, then attach the handle to the drawer front face by th...

ASSEMBLY INSTRUCTIONS Step 5: Assemble Cart Door 1. Remove the two phillips pan head screw on the cart door handle and use these two screws to install the handle on to the cart door right. 2. Place cart door right on an angle over the right door pivot. 3. Tilt the top of the door toward the grill, w...

18 ASSEMBLY INSTRUCTIONS Step 6: Assemble Side Shelf Left 1. Loosen the Four (4) 5/16-24 hex head screws located on the left grill side. 2. Attach the left side shelf by inserting the four (4) screws on the side of the grill head into the four (4) keyhole slots on the left side shelf. Note: Be caref...

19 ASSEMBLY INSTRUCTIONS Step 7: Assemble Side Burner Cover & Igniter Module 1. Remove the brass burner cap attached with tape along with side burner grate and set aside. 2. Remove the two (2) phillips pan head screws from the handle and use these screws to attach the handle on the side burner d...

1. Loosen the four (4) 5/16-24 hex head screws. 2. Attach the side burner shelf by inserting the four (4) screws on the side of the grill head into the four (4) keyhole slots on the side burner shelf. 3. Tighten all four (4) screws to secure the side burner shelf. 4. Install one (1) self-tapping scr...

ASSEMBLY INSTRUCTIONS Step 9: Assemble the Side Valve 1. Using a Phillips screwdriver, remove the 2 screws from the side burner valve assembly. 2. Push the valve stem out through the opening in the front of the side burner shelf, lining up the threaded holes in the side burner valve assembly with th...

ASSEMBLY INSTRUCTIONS Step 10: Assemble the Side Burner Casting 1. Remove the two phillips pan head screws from the side burner casting. 2. Angle the side burner casting and insert it into the center hole on the side burner tray. 3. Slide the side burner casting back in position to get the side burn...

ASSEMBLY INSTRUCTIONS Step 11: Assemble Igniter Module A A. Igniter module B. Side burner igniter wire C. Main burner igniter wires D. Back IR burner igniter wire B C 1. Connect loose igniter wires from the grill to the open terminals of the igniter. Note: The igniter is designed in such a way that ...

ASSEMBLY INSTRUCTIONS Step 12: Assemble the Side Burner Accessories 1. Center the brass burner cap on top of the side burner head. 2. Place the side burner grate onto the side burner tray. Position the 3 longer legs of the grate into the holes around the side burner. 3. Place the side burner griddle...

ASSEMBLY INSTRUCTIONS Step 13: Assemble the Drip Pan 1. Pull out the top drawer. 2. Open the right cart door. 3. Slide the drip pan onto the drip pan guides underneath the grill head assembly. A B A. Drip pan B. Drip pan guides 26

27 A B C A. Flavor grids B. Main cooking grates C. Bread warming rack D. Back Ir burner wind sheild 1. Insert the flavor grids into the cutouts with triangle ridges facing up. 2. Install main cooking grates on the ledges provided on the grill to create the cooking surface. 3. Use two self-tapping sc...

28 INSTALLATION REQUIREMENTS Select a location that provides minimum exposure to wind and traffic paths. The location should be away from strong draft areas. Do not obstruct flow of combustion and ventilation air. Clearance to combustible construction: ■ A minimum of 24” (61 cm) from grill hood side...

Product Dimensions 53.625” (136.3cm) 45” (114.4cm) 33.875” (86.1cm) 32” (81.3cm) 13.125” (33.4cm) 21” (53.3cm) 20.2” (51.3cm) Observe all governing codes and ordinances. IMPORTANT: This installation must conform with all local codes and ordinances. In the absence of local codes, installation must co...

Gas Supply Line Pressure Testing Testing above ½ psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge): The grill and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures greater than ½ psig (3.5 kPa). Testing below...

32 OUTDOOR GRILL USE Control Panel OFF P US H & T UR N H L M OFF P US H & T UR N H L M OFF P U S H & T UR N H L M B C D F E A. Back IR burner control knob B. Left burner control knob C. Middle Left burner control knob D. Middle right burner control knob E. Right burner control knob F. Ig...

Using Your Outdoor Grill (cont.) Manually Lighting Grill 1. Do not lean over the grill. 2. Remove the manual lighting extension and attach a match to the split ring. 3. Strike the match to light it. 4. Guide the lit match between the grill grate and one of the slots in the flavor grid. 5. Push in an...

Using Your Outdoor Grill (cont.) Using Your Rotisserie Burner The grill rotisserie burner is designed to cook items from the back using infrared heat. The rotisserie burner is an infrared type which provides intense searing radiant heat. Preferred by chefs over other cooking methods, this intense he...

Using Your Back IR Burner (cont.) PROTECTION OF INFRARED BURNERS The burners of your grill are designed to provide a long life of satisfactory performance. However, there are steps you must take to prevent cracking of the burner's ceramic surfaces, which will cause the burners to malfunction. The fo...

TIPS FOR OUTDOOR GRILLING 36 Before Grilling ■ Thaw food items before grilling. ■ Lightly oil the grill grates or the food when cooking low-fat cuts of meat, fish or poultry, such as lean hamburger patties, shrimp or skinless chicken breasts. ■ Using too much oil can cause gray ash to deposit on foo...

OUTDOOR GRILL CARE Replacing the Igniter Battery If igniters stop sparking, the battery should be replaced. 1. Unscrew igniter button cap counter clockwise to remove. 2. Remove battery from the battery compartment. 3. Replace with a new alkaline “AA” size battery. Install battery with negative end i...

TROUBLE SHOOTING Grill will not light ■ Is the 20 lb LP gas fuel cylinder valve turned off? Turn the 20 lb LP gas fuel cylinder on. ■ Is the grill properly connected to the gas supply? Contact a trained repair specialist or see Installation Instructions. ■ Is there gas in the 20 lb LP gas fuel cylin...

41 REPLACEMENT PARTS Hood Assembly Front Face Overlay FCTG3308001 FCTG3308006 1 set 1 set Hood Handle Amana Logo FCTG3308002 FCTG2608008 1 pcs 1 pcs Temp Guage Front Face Heat Shield FCCS0007030 FCTG3308007 1 pcs 1 pcs Hood Support Assy. Manifold & Valve Assy. FCTG3308003 FCTG3308008 1 set 1 pcs...

AMANA® is a registered trademark of Maytag Corporation or its related companies and is used under license to Sure Heat Manufacturing © 2008.All rights reserved. RACEZ00045A 11/07 Printed in China LIMITED WARRANTY Sure Heat Mfg warrants that for 2 years from the date of purchase, the stainless steel ...