Altinex MT115-110 - Manual

MULTITASKER 400-0433-003 4 PRODUCT DESCRIPTION 4 VIDEO EQUALIZATION FOR INPUT 2 AUDIO INPUT 2 4TP OUTPUT 1 4TP OUTPUT 2 BOTTOM RETAINER SCREW AUDIO INPUT 1 RGBHV/YPbPr TOP RETAINER SCREW VIDEO EQUALIZATION FOR INPUT 1 INPUT 1 INPUT 2 RGBHV/YPbPr

MULTITASKER 400-0433-003 5 APPLICATION DIAGRAMS 5 DIAGRAM 1: TYPICAL SETUP MT115-110 TP115-111 TP115-111

MULTITASKER 400-0433-003 6 DIAGRAM 2: INTERNAL VIEW MP POWER GREEN PLUG and PLAY BLUE RED VER HOR GREEN DETECT SIGNAL PAIR 4 PAIR 2 PAIR 3 PAIR 1 PAIR 4 PAIR 2 BLUE RED VER HOR MT115-110 PAIR 3 PAIR 1 VIDEO 15-PIN HD VIDEO 15-PIN HD 4TP 4TP SYNC PROCESSING SYNC PROCESSING PLUG and PLAY AUDIO 3.5mm L...

MULTITASKER 400-0433-003 7 DIAGRAM 3: SWITCH SETTINGS EQ2 SW3 GAIN2 SW5 EQ1 GAIN1 SW4 SW6 Set SW6 to SW for software control and HW for a fixed gain = 1. Set SW5 to SW for software control and HW for a fixed gain = 1. Set SW4 to SW for software control and HW for hardware control. Set SW3 to SW for ...

MULTITASKER 400-0433-003 8 INSTALLING YOUR MT115-110 6 Step 1. Determine the appropriate switch settings using Diagram 3 on page 7. Step 2. Turn off power to the MultiTasker system and disconnect from AC power. Step 3. Remove a slot cover (MT200-101) from one of the unused slots. Identify the slot n...

MULTITASKER 400-0433-003 9 7.2 DESCRIPTION OF COMMANDS Each command consists of three parts: Function, Card ID, and Unit ID. [ Function , Card ID , Unit ID ] Example: [VERC3U2] VER= Function C3 = Card ID or Group ID U2 = Unit ID (optional for Unit ID 0) For Function, see a detailed explanation under...

MULTITASKER 400-0433-003 12 Example: Set the equalization on Input 2 of C3 to a value of 32 by sending the command [EQ2=32C3]. The card will respond with feedback of “[ ]” once the command is executed. 12. [GAIN] This command displays the gain setting for an input and selects that input for adjustme...

MULTITASKER 400-0433-003 13 ID COMMANDS The default card ID is the same as the card slot number. The next several commands allow the user to change the card ID to a value other than the slot number. Once the ID is changed, moving the card to another slot will not change the card ID. If a card in slo...

MULTITASKER 400-0433-003 15 Example: G5 consists of the C2, C4, and C6. Remove only C4 and C6 from the group by sending the command [RMC4C6G5]. The system will return the following feedback: [G5=C2] 24. [RMG] This command may be used to delete an entire group, or all groups. REMOVE A GROUP Remove al...

MULTITASKER 400-0433-003 16 Group Commands 22) [WR] Group multiple cards 23) [RMC] Remove members from group 24) [RMG] Delete group 25) [RD] Display group members 7.4 MENU MODE Menu Mode commands allow virtually the same functionality as programming commands. Unlike the programming commands in the p...

MULTITASKER 400-0433-003 17 7.4.4 MT115-110 MENUS Following are the menus available to the MT115-110 . The first menu is the Main Menu only. The second listing is an expanded view of the card’s sub-menus. The expanded menu contains values that indicate the current setting or value of a parameter. Th...

MULTITASKER 400-0433-003 18 7.4.5 MENU MODE EXAMPLES All Menu Mode examples assume an MT115-110 is installed in slot 3. Start by clicking the mouse in the Terminal Window. Press ENTER and a list of available cards will be displayed. 1. Set Video Equalization Follow the keystrokes below to set the vi...

MULTITASKER 400-0433-003 19 Cause 2: Signal is bad or missing. Solution 1: Make sure the output is connected to the TP receiver. If there is still no display, see Solution 2. Solution 2: Bypass the MT115-110 and TP receiver and connect the output of the source directly to the monitor. If the display...