Altinex MT113-101 - Manual

MULTITASKER™ 400-0209-002 6 6 APPLICATION DIAGRAMS 5 DIAGRAM 1: MT113-100 TYPICAL SETUP DIAGRAM 2: MT113-101 TYPICAL SETUP

MULTITASKER™ 400-0209-002 9 9 INSTALLING YOUR MT113-100/101 6 Step 1. Turn off power to the MultiTasker enclosure. Step 2. Slide the MT113-100/101 into an available slot in the MultiTasker Enclosure in order to connect to the bus. Make sure that the MT113-100/101 card fits into place. Step 3. Secure...

MULTITASKER™ 400-0209-002 11 11 690-0122-015 = Version 015 or later. 690-0123-004 = Version 004 or later. 690-0124-018 = Version 018 or later. NOTE: In MTSetup™, send the command [VER] from the Terminal W indow. The system will respond with feedback similar to the following: [690-0122-015 690-0123-0...

MULTITASKER™ 400-0209-002 15 15 Command Format: [RUP=xxCnUi] xx = Stop Level (xx = # from 01-16) Cn = Card ID (n = # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example: Ramp the output volume from a starting level of 1 up to 10. Send the command [RUP=10C8] and receive the following feedba...

MULTITASKER™ 400-0209-002 17 17 32. [RSI] This command resets the card ID's in the system. After sending this command, each card ID in the system will match the slot number of the card. Use this command along with the SID commands that follow. The [RSI] command MUST be used prior to changing Card ID...

MULTITASKER™ 400-0209-002 19 19 REMOVE ALL GROUPS Remove all the members from every group, effectively deleting all groups. Command Format: [RMG * Ui] Ui = Unit ID (i = # from 0-9) Example: Group 1 consists of cards 1 and 2. Group 2 consists of cards 1, 2, 3, 4 and 5. Delete all the groups by sendin...

MULTITASKER™ 400-0209-002 20 20 22) [CLR] Reset card to default values 23) [RUP] Ramp volume UP to max (16) 24) [RUP=] Ramp volume UP to a value 25) [RDN] Ramp volume DOWN to min (1) 26) [RDN=] Ramp volume DOWN to a value 27) [RST] Stop ramping 28) [RAMP] Display ramp rate 29) [RAMP=] Set ramp rate ...

MULTITASKER™ 400-0209-002 21 21 7.4.2 USING MENU MODE SUGGESTION: Before using the menu mode, it is best to disable the automatic feedback feature. The values and current settings will be displayed in the menu mode, but the automatic feature will display after each setting change making the menus di...

MULTITASKER™ 400-0209-002 22 22 2. Set Input 3 Volume Starting from the Main Menu, set Input 3 volume level to 16. Follow the keystrokes below. 2 Select SETUP Menu 2 Select Set Input Volume 3 Select Input 3 Volume 16 Enter 16 NOTE The system may echo the 1 and the 6 entries, depending on the setting...

MULTITASKER™ 400-0209-002 23 23 Cause 2: The card settings are wrong. Solution: Verify the card volume settings are at maximum and that mute is off. (See section 7). If no sound is present, see Cause 3. Cause 3: Cable connections are incorrect. Solution: Make sure the cables are connected properly a...