Altinex MT110-100/102 - Manual

MULTITASKER™ 400-0132-005 5 5 APPLICATION DIAGRAM 5 Diagram 1: TYPICAL SETUP

MULTITASKER™ 400-0132-005 7 7 Diagram 2: Internal View MT110-100 OUT 1 TERMINAL BLOCKS OUT 2 OUT 3 OUT 4 OUT 5 OUT 6 MATRIX SWITCHER + - IN 1 IN 2 IN 3 IN 4 TERMINAL BLOCKS IN 5 IN 6 IN 7 IN 8 IN 9 IN 10 IN 12 IN 11 OUT 7 OUT 8 MATRIX CONTROL IN 15 IN 14 IN 16 IN 13 - + - + - + - + - + - + - + - + -...

MULTITASKER™ 400-0132-005 9 INSTALLING YOUR MT110-100/102 6 Step 1. Turn off power to the MultiTasker™ enclosure. Step 2. Slide the MT110-100/102 into an available slot in the MultiTasker™ Basic Enclosure in order to connect to the bus. Make sure that the MT110-100/102 card fits into place. Secure t...

MULTITASKER™ 400-0132-005 11 Example: If Input 1 is connected to all outputs, but only 1 through 4 are on, the feedback after sending the command [C4S], for slot 4, would be similar to the following: CONFIGURATION:Matrix:16x8, In-Offset=0, Out-Offset=0CONNECTION OUTPUT VOLUME In01-Out01 ON 32/32 In0...

MULTITASKER™ 400-0132-005 14 If ‘F’ is included, use the [OFFmCnPF]command or the [OFFmCnFP] command. FEEDBACK OPERATION After processing a command, an “OK” or “[ERR001]” will be returned as feedback if ‘F’ is included at the end of a command string. Command Format: [OFF…..F] Example: [OFF1C2F]: if ...

MULTITASKER™ 400-0132-005 15 Command Format: [ImO * CnUi] m = Input (m = # from 1 to 8) Cn = Card ID (n = slot # from 1 to max slots) Ui = Unit ID (i = # from 0 to 9) Example: Connect Input 1 to all outputs for the MT110-102 in slot 5. Send the command [I1O*C5] and Input 1 will be connected to all o...

MULTITASKER™ 400-0132-005 16 Some cards require more than one slot in the MultiTasker™ system. As an example, some matrix switcher cards require 4 slots. If there are five of these cards installed, they would be numbered C4, C8, C12, C16 and C20. Changing the Card ID allows the user to define the ca...

MULTITASKER™ 400-0132-005 23 Example: In order to display the RS-232 commands available for the MT110-102 card in slot 2, send the command [HELPC2]. The commands along with a brief description will be displayed in the terminal window. 7.3. SUMMARY OF COMMANDS Card Commands 1) [VER] Receives software...

MULTITASKER™ 400-0132-005 24 TROUBLESHOOTING GUIDE 8 We have carefully tested and have found no problems in the supplied MT110-100/102 ; however, we would like to offer suggestions for the following: 8.1 LED IS NOT LIT Cause 1: Card cage is not plugged in. Solution: Plug card cage in. If the LED lig...

MULTITASKER™ 400-0132-005 25 Solution 2 : Set the volume of the destination amplifier to a reasonable level. If there is still no sound, call ALTINEX at (714) 990-2300. 8.4. DISTORTED SOUND Cause 1: The source level is above 1Vp-p Solution: Make sure that the source level is below 1V p-p. If the sou...