Altinex MT103-123 - Manual

MULTITASKER 400-0374-005 5 PRODUCT DESCRIPTION 4 AUDIO OUTPUT AUDIO OUTPUT TOP RETAINER SCREW BOTTOM RETAINER SCREW VIDEO OUTPUT S-VIDEO INPUT C-VIDEO OUTPUT VIDEO EQUALIZATION UNBALANCED STEREO BALANCED STEREO 4TP INPUT RGBHV/YPbPr

MULTITASKER 400-0374-005 6 APPLICATION DIAGRAMS 5 DIAGRAM 1: TYPICAL SETUP AUDIO C-VIDEO S-VIDEO OR OR YPbPr RGBHV/ MT103-123 DA1930CT

MULTITASKER 400-0374-005 7 DIAGRAM 2: RJ-45 PINOUT 8 7 6 5 4 3 2 1 FRONT 1 8 1 8 Brown Brown/White Green Blue/White Green/White Orange Orange/White TOP Blue RJ-45 Output Signals Pin No. Table 4 Standard 568B Wiring Color Code

MULTITASKER 400-0374-005 8 DIAGRAM 3: INTERNAL VIEW DETECT SIGNAL AUDIO SEPARATOR RJ-45 TWISTED PAIR 3 PAIR 4 INPUT PAIR 1 PAIR 2 15-PIN HD LP LP SYNC-ON-GREEN PROCESSING SYNC LP LP - - + + 5-PIN TB R1- BAL. AUDIO 3.5 mm UNBAL. STEREO AUDIO STEREO LEFT L1- RIGHT L1+ VIDEO Y Pb Pr RGBHV/ VER R1+ GREE...

MULTITASKER 400-0374-005 9 DIAGRAM 4: SWITCH SETTINGS HW = Hardware control SW = Software control VIDEO EQUALIZATION (EQ) The MT103-123 has an internal switch with 6 positions to achieve the following features: GAIN and SYNC OPTIONS Video Gain ON=1 x1, OFF=x2 Factory Default = x1 Sync-On-Green (ON/O...

MULTITASKER 400-0374-005 10 INSTALLING YOUR MT103-123 6 Step 1. Determine the settings required for Gain, Sync-On-Green, Horizontal Sync Polarity,and Vertical Sync Polarity. If necessary to change the factory defaults, set the switches per Diagram 4 on page 8. Step 2. Turn off power to the MultiTask...

MULTITASKER 400-0374-005 11 7.2 DESCRIPTION OF COMMANDS Each command consists of three parts: Function, Card ID, and Unit ID. [ Function , Card ID , Unit ID ] Example: [VERC3U2] VER = Function C3 = Card ID or Group ID U2 = Unit ID (optional for Unit ID 0) For Function, see a detailed explanation und...

MULTITASKER 400-0374-005 14 14. […S] – Save This command will save the configuration command being sent in memory. When sending the command [EQ=10C4S], after reset or power-up, the equalization level on C4 will be set to 10. 15. [TEST] This command performs a series of tests on the internal memory. ...

MULTITASKER 400-0374-005 15 18. [SIDn] This command sets all the cards installed in the MultiTasker system to the same card ID. After sending this command, all cards will be addressed with the same ID. Use caution when sending this command to a system with multiple board types. Command Format: [SIDn...

MULTITASKER 400-0374-005 19 4: HELP This selection displays a list of commands available for the MT103-123 along with a brief description. It is equivalent to the [HELP] command. ESC This selection returns you to the parentmenu with the listing of all cards. 7.4.5 MENU MODE EXAMPLES All Menu Mode ex...

MULTITASKER 400-0374-005 20 TROUBLESHOOTING GUIDE 8 We have carefully tested and have found no problems in the supplied MT103-123. However, we would like to offer suggestions for the following: 8.1 LED IS NOT RED The LED should be on and red when power is applied and there is no video signal present...

MULTITASKER 400-0374-005 21 8.4 NO REMOTE IMAGE Cause 1: The source has a problem. Solution: Check the image on a local monitor and verify the quality is good. If the local image is good, see Cause 2. Cause 2: Video equalization required. Solution: Adjust the Video Equalization controlon the MT103-1...