Allied Telesis Rapier Series - Manual

Allied Telesis Rapier Series

Allied Telesis Rapier Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
Page: / 8

Table of Contents:

  • Page 2 – Patch file details are listed in Table 2:
  • Page 4 – Executing a ping to the IP address 0.0.0.0 did not return an; error message. Also, when the TRACE command
  • Page 5 – inuse; IGMP Snooping All-Group Entry; IGMP snooping; Commands; Level: 3
  • Page 6 – Modified Command; Syntax; interface; Description; This enhancement includes the line “; Disabled All-groups ports; ” on the output; Examples; To show information about IGMP, use the command:; See Also
  • Page 7 – New Commands; ENABLE IP IGMP ALLGROUP
  • Page 8 – Availability; licence or password is not required to use a patch.
Loading the manual

S i m p l y c o n n e c t i n g t h e w o r l d

Patch Release Note

Patch 86253-03
For Rapier Series Switches

Introduction

This patch release note lists the issues addressed and enhancements made in
patch 86253-03 for Software Release 2.5.3 on existing models of Rapier series
switches. Patch file details are listed in Table 1.

This release note should be read in conjunction with the following documents:

■

Release Note: Software Release 2.5.3 for Rapier Switches and AR400 and
AR700 Series Routers (Document Number C613-10362-00 Rev A) available
from

www.alliedtelesyn.co.nz/documentation/documentation.html

.

■

Rapier Switch Documentation Set for Software Release 2.5.1 available on
the Documentation and Tools CD-ROM packaged with your switch, or
from

www.alliedtelesyn.co.nz/documentation/documentation.html

.

WARNING: Using a patch for a different model or software release may cause
unpredictable results, including disruption to the network. Information in this
release note is subject to change without notice and does not represent a
commitment on the part of Allied Telesyn International. While every effort has
been made to ensure that the information contained within this document and
the features and changes described are accurate, Allied Telesyn International
can not accept any type of liability for errors in, or omissions arising from the
use of this information.

Table 1: Patch file details for Patch 86253-03.

Base Software Release File

86s-253.rez

Patch Release Date

30-July-2003

Compressed Patch File Name

86253-03.paz

Compressed Patch File Size

191102 bytes

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Patch file details are listed in Table 2:

2 Patch Release Note Patch 86253-03 for Software Release 2.5.3 C613-10382-00 REV B Some of the issues addressed in this Release Note include a level number. This number reflects the importance of the issue that has been resolved. The levels are: Features in 86253-03 Patch 86253-03 includes all issue...

Page 4 - Executing a ping to the IP address 0.0.0.0 did not return an; error message. Also, when the TRACE command

4 Patch Release Note Patch 86253-03 for Software Release 2.5.3 C613-10382-00 REV B The maximum number of firewall sessions had decreased since software release 86s-241. This issue has been resolved. Previously, an incorrect source address was used for router advertisements that were sent over an IPv...

Page 5 - inuse; IGMP Snooping All-Group Entry; IGMP snooping; Commands; Level: 3

Patch 86253-03 For Rapier Series Switches 5 Patch 86253-03 for Software Release 2.5.3C613-10382-00 REV B The ENABLE RSVP INTERFACE command did not succeed if IP was enabled after the RSVP interface had been created. Now, ENABLE RSVP INTERFACE will succeed regardless of when IP is enabled as long as ...

Other Allied Telesis Models

All Allied Telesis Other