Allied Telesis Patch 86261-04 - Manual
Allied Telesis Patch 86261-04 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 4 – ADD IGMPSNOOPING ROUTERADDRESS; ADD IGMPSNOOPING ROUTERADDRESS=; Description; SET IGMPSNOOPING ROUTERMODE; Syntax; SET IGMPSNOOPING ROUTERMODE=; Description; This command sets the mode of operation for IGMP Snooping.
- Page 5 – DELETE IGMPSNOOPING ROUTERADDRESS; SHOW IGMPSNOOPING ROUTERADDRESS; SHOW IGMPSNOOPING ROUTERADDRESS; Figure 1: Example output for SHOW IGMPSNOOPING ROUTERADDRESS; IGMP Snooping Router Address; Level: 2
- Page 10 – Level: 4
- Page 15 – IGMP Snooping is active, L3FILT is activated; NAT is; Current Temperature
- Page 16 – due to the port bandwidth.; Reply
- Page 23 – Availability; licence or password is not required to use a patch.
S i m p l y c o n n e c t i n g t h e w o r l d
Patch Release Note
Patch 86261-04
For Rapier and AT-8800 Series Switches
Introduction
This patch release note lists the issues addressed and enhancements made in
patch 86261-04 for Software Release 2.6.1 on existing models of Rapier and
AT-8800 Series switches. Patch file details are listed in Table 1.
This release note should be read in conjunction with the following documents:
■
www.alliedtelesyn.co.nz/documentation/documentation.html
.
■
www.alliedtelesyn.co.nz/documentation/
documentation.html
.
WARNING: Using a patch for a different model or software release may cause
unpredictable results, including disruption to the network. Information in this
release note is subject to change without notice and does not represent a
commitment on the part of Allied Telesyn International. While every effort has
been made to ensure that the information contained within this document and
the features and changes described are accurate, Allied Telesyn International
can not accept any type of liability for errors in, or omissions arising from the
use of this information.
Table 1: Patch file details for Patch 86261-04.
Base Software Release File
86-261.rez
Patch Release Date
19-Nov-2003
Compressed Patch File Name
86261-04.paz
Compressed Patch File Size
261628 bytes
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
4 ADD IGMPSNOOPING ROUTERADDRESS Patch Release Note Patch 86261-04 for Software Release 2.6.1 C613-10386-00 REV D This PCR introduces an enhancement that extends an issue that was resolved in PCR 03890, in which switch port entries are only created for special router multicast addresses. It is now p...
Patch 86261-04 For Rapier and AT-8800 Series Switches SHOW IGMPSNOOPING ROUTERADDRESS 5 Patch 86261-04 for Software Release 2.6.1C613-10386-00 REV D DELETE IGMPSNOOPING ROUTERADDRESS Syntax DELETE IGMPSNOOPING ROUTERADDRESS=ipaddr[,...] where • ipaddr is a reserved IP multicast address in dotted dec...
10 SHOW IGMPSNOOPING ROUTERADDRESS Patch Release Note Patch 86261-04 for Software Release 2.6.1 C613-10386-00 REV D The entry for the FanAndPs group in the private MIB did not return valid information. This issue has been resolved. On AT-8848 switches, a STP loop occurred if the Gigabit uplink port ...
