Allied Telesis AT-9924T - Manual

x900 Series Switch and SwitchBlade ® x908 6 Selecting a Site Before you install the switch, review the following considerations about its location. ■ AT-8948, x900-48FE, x900-48FS, and AT-9900 switches require an ambient temperature from 0º C to 50ºC (32º F to 122º F). ■ AT-9924Ts, x900-12XT/S, x900...

Installation and Safety Guide 7 Installing the Switch Ports on the switch are suitable only for connections within buildings (intra-building) and with cables unexposed to the outside. You can install the switch on a level surface, such as a desktop or bench, or in a standard 19-inch rack. Some switc...

x900 Series Switch and SwitchBlade ® x908 8 ■ All bare conductors must be coated with an appropriate antioxidant compound before making crimp connections. Warning Both AC and DC versions of this equipment must be earthed through the power cables provided. On a level surface 1. Ensure the area has su...

Installation and Safety Guide 11 Applying Power to the Switch Power supply bays are in the rear of the switch. Depending on the model, the switch may have a PSU, FOM, or blanking plate over a power supply bay. Connecting an AC power supply Follow these instructions to connect one of the following to...

x900 Series Switch and SwitchBlade ® x908 12 1. Plug the AC power cord that is provided into the power inlet on the PSU. 2. Connect the power cord to the main power source. 3. On the AT-PWR05, set the Run/Standby switch to Run. 4. Check that the PSU LED on the front panel of the switch is lit green....

x900 Series Switch and SwitchBlade ® x908 14 8. Ensure that the circuit breaker is off for the supply circuit and the Run/ Standby switch on the PSU. Release the Run/Standby switch so that it is not pushed in (which is the Off position). 9. Connect the supply cable wires to the circuit breaker. 10. ...

Installation and Safety Guide 17 Connecting to the Switch All x900 Series switches and the SwitchBlade x908 can be configured using the Command Line Interface (CLI) and the Graphical User Interface (GUI). The procedure and command syntax varies depending on whether the switch is running the AlliedWa...

x900 Series Switch and SwitchBlade ® x908 20 Using the AlliedWare Plus Operating System GUI Follow this procedure to establish a connection to an x900 or x908 series switch, so you can use the GUI to configure the switch. 1. Select a PC to use and identify its subnet. You can browse to the switch fr...

x900 Series Switch and SwitchBlade ® x908 22 Using the AlliedWare Operating System CLI Depending on the model, an ASYN0/CONSOLE and/or ETH0 port is on the front of the switch for installation and maintenance. 1. To use the ETH0 port , physically connect it to the terminal or PC, and check that the p...

Installation and Safety Guide 23 4. Change the password. A manager account with the default password is a serious security risk. Remember the new password because there is no way to retrieve it if you forget it. To change the account password, use the set password command. 5. Configure online help. ...

x900 Series Switch and SwitchBlade ® x908 24 Using the AlliedWare Operating System GUI Follow this procedure to establish a connection to an AT-9900 series switch, so you can use the GUI to configure the switch. 1. Select a PC to use and identify its subnet. You can browse to the switch from any PC ...

Installation and Safety Guide 25 Checking LEDs The following LEDs report operations and faults on x900 Series and SwitchBlade x908 switches: ■ “System LEDs” on page 25 ■ “Stacking LEDs” on page 27 ■ “PWR01 LEDs” on page 27 ■ “PWR02 LEDs” on page 27 ■ “PWR05 AC LEDs” on page 28 LEDs for Ethernet port...

x900 Series Switch and SwitchBlade ® x908 28 PWR05 LEDs The following is a diagram of the LEDs in the PWR05 power supply units: PWR05 AC LEDs The following table describes LEDs on the PWR05 AC power supply unit for the SwitchBlade x908. IN LED POWER CONNECTOR OUT LED FAULT LED LED State Description ...

x900 Series Switch and SwitchBlade ® x908 30 Obtaining Documentation and Resources The complete document set for x900 Series switches and SwitchBlade x908 includes: ■ this Installation and Safety Guide ■ the x900 Series Switch and SwitchBlade ® x908 Hardware Reference , which contains detailed infor...

Installation and Safety Guide 31 AT-TFTP Server for Windows is a TFTP ( Trivial File Transfer Protocol ) server for transferring software versions, configuration scripts and other files between a PC and the switch. You download AT-TFTP Server from www.alliedtelesis.com/support/software . CD-ROM Some...

x900 Series Switch and SwitchBlade ® x908 32 Standards Where applicable, the products in this document meet the following standards: Category Approval Agency and Requirement Safety UL60950-1 CAN/CSA-C22.2 No. 60950-1-03 EN60950-1 AS/NZS 60950.1 EN 60825-1 EN 60825-2 21 CFR 1040 Electromagnetic FCC C...

Installation and Safety Guide 33 Safety WARNING: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. WARNING: Class 1 Laser product. WARNING: Do not stare into the laser beam. CAUTION: Use of controls or adjustments of...

Installation and Safety Guide 35 Sicherheit WARNUNG: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen. WARNUNG Laserprodukt der Klasse 1. WARNUNG Nicht direkt in den Strahl blicken. ACHTUNG: GEFÄHRLICHE SPAN...

Installation and Safety Guide 37 Sikkerhed ADVARSEL: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. ADVARSEL Laserprodukt av klasse 1. ADVARSEL Stirr ikke på strålen. ELEKTRISKE FORHOLDSR...

x900 Series Switch and SwitchBlade ® x908 38 med samme eller en tilsvarende type der anbefales af producenten. Kassér brugte batterier i overensstemmelse med producentens instruktioner. ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og national lovgivning for elektriske ...

Installation and Safety Guide 39 Veiligheid WAARSCHUWING: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. WAARSHUWING Klasse-1 laser produkt. WAARCHUWING Neit in de straal staren. WAARSCHUWINGEN MET BETREKKING TOT...

Installation and Safety Guide 41 Sécurité MISE EN GARDE : dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. ATTENTION Producit laser di classe 1. ATTENTION Ne pas fixer le faisceau des yeux. ...

Installation and Safety Guide 43 Remarque: Ce système peut fonctionner avec des systèmes C.C. dotés d’une mise à la terre positive ou négative. Turvallisuus VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä ta...

x900 Series Switch and SwitchBlade ® x908 44 Litiumparisto - Vaihdon voi suorittaa vain koulutettu ja pätevä teknikko. Varoitus : Räjähdysvaara, jos paristo on vaihdettu väärin. Vaihda vain samaan tai vastaavaan tyyppiin, jota valmistaja suosittelee. Hävitä käytetyt paristot valmistajan ohjeiden muk...

Installation and Safety Guide 45 Norme di Sicurezza AVVERTENZA: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti. AVVERTENZA Prodotto laser di Classe 1. AVERTENZA Non fissare il raggio con...

x900 Series Switch and SwitchBlade ® x908 46 Batteria al litio - Va sostituita solo da un tecnico specializzato e qualificato. ATTENZIONE: l'errata sostituzione della batteria può causare pericolo di esplosioni. Sostituire solamente con lo stesso tipo o con uno equivalente raccomandato dal produttor...

Installation and Safety Guide 47 Sikkerhet ADVARSEL: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. ADVARSEL Laserprodukt av klasse 1. ADVARSAL Stirr ikke på strålen. ELEKTRISITET ADVARSEL: FARE...

x900 Series Switch and SwitchBlade ® x908 48 ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale elektriske koder. Advarsel: VED TILKOPLING TIL ET LIKESTRØMSNETT, SKAL DU BARE MONTERE UTSTYRET PÅ ET STED HVOR UVEDKOMNE IKKE HAR ADGANG. Merknad: En kanalkabel er nødvendig for å k...

Installation and Safety Guide 49 Segurança AVISO: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas. AVISO Produto laser de classe 1 AVISO Não olhe fixamente para o raio. AVISOS SOBRE CARACTERÍSTI...

Installation and Safety Guide 51 Seguridad ADVERTENCIA: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. ¡ADVERTENCIA! Producto láser Clase 1. ¡ADVERTENCIA! No mirat fijamente e...

Installation and Safety Guide 53 Nota: Este sistema funcionará con sistemas de CC con conexión positiva o negativa a tierra. Säkerhet VARNING: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. VARNING! Laserprodukt av klas...